G-Force to release pneumatic frames for the Mags

[Smoothice]

So what's Garf's email - because I'd like to pick one up now. I'm assuming enough people canceled that there should be some available...

:rofl: You think cancelling was an option?

You can buy mine for $300

[LK-13]

So what's Garf's email - because I'd like to pick one up now. I'm assuming enough people canceled that there should be some available...

you would be much better off going D.I.Y. with a kit.
much more cost effective.

linky => http://www.automags.org/forums/showthread.php?t=226161

[UThomas]

Nah - I like the fit and finish. Not looking for most cost effective. Then again, not looking to pay $100 over retail either

[TnDeathInc]

Nah - I like the fit and finish. Not looking for most cost effective. Then again, not looking to pay $100 over retail either

100 over retail would be if these were still being made, they are rare breed, a collectors item. 300 is a deal imho.

[Danterwhoo]

Well I got mine today......but I'm waiting for the internal LPR to mount everything, I don't want to buy several LPR's just to play with this thing. But it looks great......except for the grips anyone know which ones will fit these holes?

[seekandestroy78]

im pretty sure these are an original hole pattern.

[UThomas]

So does anyone actually have Garf's email?

[babyface]

So does anyone actually have Garf's email?

gforce_pb AT yahoo.com

[Andrew Cunje]

you would be much better off going D.I.Y. with a kit.
much more cost effective.

linky => http://www.automags.org/forums/showthread.php?t=226161

lets keep on topic here...this thread isnt about DIY crud....this is about garfs frame...which is, sorry, better than any diy ive had in my hands...plus you don't have to do anything! : ) comes ready rather than dremmelling and drilling

IF YOU CAN GET YOUR HAND ON A GFORCE FRAME!!! BY ALL MEANS... DO IT... went ballin today and had all kinds of people eyeballin' the hell out of it

[Andrew Cunje]

Before you do anything rash,
WRAP THE SCREW IN TEFLON TAPE AND REINSTALL!!

the Teflon tape will dampen vibration and tighten the fit of the screw while still allowing it to be removed with out trashing anything.

just use some red OR blue loctite...its not perminaent by any means...it can be removed with a lighter to warm up the loctite and it'll slide out like a pig covered in ky

[matteusz]

Anyone willing to trade their frame for this:

http://www.automags.org/forums/showthread.php?t=234873

Mat

[Twistedpsyche]

Picked mine up at the PO today. I'll try and get some pics later in the week.
Of course it's still useless without the LPR and I'm not about to go buy another LPR while I wait for this one.

[skyless]

Got mine too. Im in the same boat as far as the lpr, but its nice to have it in my hands. Still need to get another valve, thinking about going classic.
Those of you running a classic, standard on/off working good?
think you can max out the valve?

Sleeper, any ideas about how to fit a ticker in there, I have one and it would need some work to make it work, does the micro rock work better. I believe i read that this frame would except an aftermarket lpr, really wondering how the gforce lprs will fit.

I may resort to external lpr if i get impatient

[Twistedpsyche]

Opened it up. I'm impressed at how light it is. The grips gotta go though. Anyone got any plans to make any replacement grips for this thing?

[custar]

Anyone got any plans to make any replacement grips for this thing?

How many people would be interested in wood grips?

custar