2009 PTP Micromag Repair Thread - PTP Washer Insert

[DoubleDutch]

Well mine is not working right. With the washer in, it seems to activate the level 10 every 3rd shot or so. Without the washer, it shoots fine, I limit the shots of course. I tried a gold spring and a black spring.

I have the breech off so I can see the bolt, it shoots a few, then the bolt will come out only halfway, vent, and recock. That is the level 10 engaging right?

Anyone know what else I might try? I am refilling my tank right now, I did have the pressure set fairly low because I had a new marker, it was at 650. I put two thin shims in it (ninja reg) and the shoebox is pumping it now.

[zondo]

Have you taken the bolt out to see if there are any signs of rubbing?

EDIT:
Just cycled mine ~100 times and no issues (X-valve with L10)

The only thing I am having trouble with is finding a barrel that screws in all the way. Only my CCM screws in easily, my Kaners go in with a little stiffness, but by Lurker and Empire twister won't go past 1.5 turns.

[doc_Zox]

Mine arrived Friday

Thanks for the parts!

Doc Zox

[DoubleDutch]

Have you taken the bolt out to see if there are any signs of rubbing?

EDIT:
Just cycled mine ~100 times and no issues (X-valve with L10)

The only thing I am having trouble with is finding a barrel that screws in all the way. Only my CCM screws in easily, my Kaners go in with a little stiffness, but by Lurker and Empire twister won't go past 1.5 turns.

There are lines on it that might be rubbing. I was able to get it to fire reliably by turning up the velocity adjustment, but now I am back to the first problem I had before, not being able to get the velocity above 220 before the valve leaks out the back. Maybe now I will put a few tanks through it now that it won't get damaged anymore, see if that alleviates the problem as reported by some.

By the way, the test firing I did was with my brand new Lurker Eigenbarrel and it threaded in just fine.

[robertsr1811]

Got my washers today. Many thanks!


On the barrel front... One of my bodies threads just fine, and the other I had to chase the threads on the body to get all my barrels to fit.

You may just need to have the threads chased. Pretty simple actually. Has happened on more than one cocker threaded gun I've owned. Seems like a lot of variation in the "standard" threads.

[GRAYGHOST]

washers came today fit nice work well THANKS RUSSEL

[alooney11]

Got my washers, fit perfectly thanks!

[ZoomZ@PTP]

Washers going out today to :

Dana
Chris
Alexander
Ben
Joe
Adam



International orders will ship out of Maine next week , those of you that sent me a request from outside the USA , your emails have been forwarded to Maine also .

[sQuidvision]

None for me in round 2?

[ZoomZ@PTP]

You should have gotten yours in the first batch ?

Is your name on the list above ?

If not sorry for the over look , resend me and email please .

[Ando]

International orders will ship out of Maine next week , those of you that sent me a request from outside the USA , your emails have been forwarded to Maine also .

Is she also sending out bodies and gear that haven't been sent out yet?

[sQuidvision]

You should have gotten yours in the first batch ?

Is your name on the list above ?

If not sorry for the over look , resend me and email please .

Its probably my fault for not including my address in my original email... another email inbound.

[DarkApollo]

:does happy dance:

[DarkApollo]

Got mine yesterday! Drops right in! Now I can finish my Pneumag conversion and actually use it!

[Almeister]

Can I still get on of these washers? I just found out about the issues people were having with their bodies. I haven't been on AO since I got my body a while back. I just tried putting my valve in for the first time and it fits fine and now I'd like to get one of these washers as a precaution before I fire it.