Precision Powder - Custom Marker Refinishing

[PrecisionPowder]

PM'ed You!

replied

Whoo Whee!!! looks great yo!!!

thank you, ill have more posted at the end of the week. i have an axe on the way for a pearl white with a custom blue pearl

[PrecisionPowder]

white pearl, with a custom blue pearl added

[XtraKargo]

PM sent.

[magicdrafna]

So i was wondering if you had any ideas what to do with this?



I had thought about having segments dipped would you want that done before sending to you for coating

[PrecisionPowder]

PM'd



also here is another mag





and here is a geo in a custom metallic blue and a custom blue pearl white

[PrecisionPowder]

[Bxmarg]

That mag is mine and Roger did a great job on it. I have a few more parts to send him. It's quality work.

[PrecisionPowder]

That mag is mine and Roger did a great job on it. I have a few more parts to send him. It's quality work.

Thank you! Looking forward to doing the next round of parts

[PrecisionPowder]

Here is a small update to the thread, two sydarms I just completed for a member here and a phantom.

[grub]

Roger, I was wondering if it was possible to powdercoat a classic valve (and have it remain functional)? I've read that stainless can be done and it looks like you have the skills, so I guess I'm just concerned about the tolerances. How thick does the coating end up to be? What finishes would be possible? Thanks for your time

-grub

[XtraKargo]

One of the rigs I'm sending in was going to include a valve as well. I'm certain it will get masked in the right places based on our discussion.

Plus like you said, he has got the skills. I'm just waiting on colors and then will be sending them in the markers soon for him to work on.

(Not to hi-jack, more of an FYI, if you wanted to wait and see how he does)

[grub]

No problem, I can't wait to see how your setup turns out.

-grub

[Jaccen]

Top notch work! I presume you're in the USA? I ask because I'm a Canuck.

[kwik175]

I have 2 mags that Roger did for me and they are amazing. My purple metallic Karta is exactly as I wanted per our discussions. The Phoenix Stormwalk project was a leap in color but turned out stunning. I recommend his work to anyone as top notch. He masks everything and the tolerances are in no way affected. Thanks again Roger.

[PrecisionPowder]

Roger, I was wondering if it was possible to powdercoat a classic valve (and have it remain functional)? I've read that stainless can be done and it looks like you have the skills, so I guess I'm just concerned about the tolerances. How thick does the coating end up to be? What finishes would be possible? Thanks for your time

-grub

I don't see why I couldn't. The valve would need to be disassembled completely first, and you would need to provide me with a few pictures of how it goes together so I can mask off any vital areas. Only the visible portions would be coated leaving it completely functional.

As far as a thickness it would depend 100% on the finish you wanted. A solid glossy color will be thinner than metallics, candies, custom flakes, or custom flat colors specifically because those require more than one coat. Typically a coat is applied at 3-5 mils (1mil = .001").

Finishes possible are as follows:
solid tone
candy
matte
wrinkle
vein
texture
river
metallic
pearl
chameleon (color changing)
or combinations of the above

Top notch work! I presume you're in the USA? I ask because I'm a Canuck.

Thank you!

Correct, I am located in Maine roughly 2 hours from Quebec. International shipping is not very costly though, I just sent back a phantom I did for someone in Canada I believe it cost $27 to send it back.

I have 2 mags that Roger did for me and they are amazing. My purple metallic Karta is exactly as I wanted per our discussions. The Phoenix Stormwalk project was a leap in color but turned out stunning. I recommend his work to anyone as top notch. He masks everything and the tolerances are in no way affected. Thanks again Roger.

You are very welcome! Thank you again for the kind words!