KAM Designs M86 Run #2

[pump]

What the trigger feel like mech?
Stock or ptp or other?

[cougar20th]

This Run has enough orders that it will happen as long as everyone gets the deposits in before the end of the pre-order (March 7). Then we begin machining.

[maverick13]

Good !

We're sure to get our frames !

[cougar20th]

Im not going to be limiting the run. The preorder will be open until March 7. Which is what I originally put in the info. I never dreamed that it would hit the 10+ this fast otherwise I would have done shorter. But I feel it would be wrong to change the end time and possibly eliminate people.

[blamtro]

Pming

[knownothingmags]

I understand a rendering only goes so far to make people comfortable so I am also willing to cut up perfectly good product to make sure everyone is happy.

should have had me print it
considering the cost that it has costed you
facepalm

[hawaiianking]

Ill take one.

[rschoi_75]

Hey Keith,
I'll take the last spot. I'm sure I'll get around to using this one too.

[cougar20th]

FYI - you guys should realize that if Cougar20th says it's going to fit, it's going to fit !!

I understand a rendering only goes so far to make people comfortable so I am also willing to cut up perfectly good product to make sure everyone is happy.

[BigEvil]

FYI - you guys should realize that if Cougar20th says it's going to fit, it's going to fit !!

[cougar20th]

Ok spent alittle time doing something painfull. Cutting one of the frames I was going to keep for myself. I had no intention of modding it but felt you all needed a real demonstration of how to modify these for sleeper mods.

Place fabco switch in the upper two mounting holes. Mark frame at bottom of the switch. Remove the switch and cut along the line & the back edge of the cavity. Removing the lower mounting screw. File slowly until lpr clears.
I did this using nothing more then a hacksaw blade and a file.


Tickler mounted and fabco mounted. You will have to cut the arm of the fabco down as nessesary. I did not as those parts belong on my M90 gun. You may also need to flip the arm on the fabco so that the air inlets are on the top with 90 degree fittings. Youll have to play some to find the exact setup.

[cougar20th]

Sorry if I'm just not remembering seeing it in the original thread, but I read that the frame can take emag magnets above the trigger. Does the included trigger have a magnet (or a place for one) in it, or would that be something that would have to happen custom from somewhere else?

Also, I'm kind of thinking about getting in on this order. I really have no need/interest in a pneu setup. Could a frame be made without the sear release hole drilled? Would just be another place to have to dig paint/dirt out of at some point with it being there.

The frames will accept emag magnets. They are not included.

All frames come with the sear releas hole. To make it otherwise means custom and more cost. The hole is pretty handy on non pnue setups. I know one of my valves has a sticky on,off so otherwise i would hsve to remove the body to get the valve out.

[Chrome]

Sorry if I'm just not remembering seeing it in the original thread, but I read that the frame can take emag magnets above the trigger. Does the included trigger have a magnet (or a place for one) in it, or would that be something that would have to happen custom from somewhere else?

Also, I'm kind of thinking about getting in on this order. I really have no need/interest in a pneu setup. Could a frame be made without the sear release hole drilled? Would just be another place to have to dig paint/dirt out of at some point with it being there.

[cougar20th]

Does anybody have a completed sleeper set up on these yet? Pictures?

Let me me cut up one this weekend. Then ill moint everything. It wont be functional. I dont have asa and wont be cutting my fabco.

[river031403]

Does anybody have a completed sleeper set up on these yet? Pictures?