Xmag CCM Feedneck Breech Mods

[BigEvil]

Remove your stock crappy feed cup and replace it with a CCM clamping feedneck. Tried and true, I have done more of these now that I can even remember. Can be done on ANY Xmag or SFL breech.


^Old Euro style breeches shown with dual detents and added set screws*

-Semi permanent, non removable. Can be take apart and replaced for anno
-Compatible with single or dual detents.
- Available in either the 1.5" cup (shown) or 1" short rise cup.

$75 per breech. Includes either type of CCM feedneck in gloss or dust finish and color of your choice. +for return shipping.

*Add $25 for SFL/Non CNC breeches that have dual detents and need set screws drilled and tapped.

2/1/2017

Inception Feed necks are on their way. I have only like 2 CCM ones left. The ID ones are +$20 added to the price. PM me for details


Some pics;

https://www.instagram.com/p/BQYB7BGAuqnb6eUneZxTOjjDiFyq_jOek78sKY0/

https://www.instagram.com/p/BQYBuKbA81KTOZ1Ff2-QNU4oD42ENlIs10V0is0/

https://www.instagram.com/p/BOn_-XZDwIaDmWiU_FfjXcBYSJj9fbwTR9C77o0/

[BigEvil]

1" feedcup on my Xmag

[DevilMan]

Woot Woot!!! So.. I want one..

Does this include the breech? Or is this a send to you and you pull the old, push the new one and send it all back?

either way works for me. Do you happen to have any "extra" vert breeches that I could buy and just have this done so I can keep my stock one? Prefer a CNC breech. But would take a plain one.

DM

[Bunny]

I can vouch for this service. BigEvil is one of the only guys I can trust with my breaches. I trust him with my coveted SFL breaches as well as a handful of my Euro Xmag breaches in the past. He knows exactly what to do

[DevilMan]

Hey Bunny.. I PM'd ya a bit back...

Can I get a breech or two from ya??

No feedneck needed.

DM

[BigEvil]

I WISH I had a stash of breeches laying around.

Service includes swapping out the old one and installing a new one, just in case I wasn't clear.

DM hit me up anytime.

[DevilMan]

I thought that's what it was. Just making sure. Do you supply the feedneck?

And yeah... if I can get a CNC breech from Bunny I'll have you do it. May keep the stock one just because. But if not, then I'll send you the original to have it done.

DM

[BigEvil]

I thought that's what it was. Just making sure. Do you supply the feedneck?

And yeah... if I can get a CNC breech from Bunny I'll have you do it. May keep the stock one just because. But if not, then I'll send you the original to have it done.

DM

Yup, If I dont have it in stock at the time I get them.

[DevilMan]

grovy.. works for me. I'll take a 1" one I'm thinking... I like the look of the low profile. It holds a rotor properly right?

can/do you have a dust black one?

DM

[Bunny]

At the moment I do not have any more breaches for sale. Most of the breaches that I bought from AGDE are not functional. I'm working on a solution though, but it will be a while. I do have extra "Xmag" feed tubes available if you would to have both the old version and the CCM version if you decided to re-anodize them.

[BigEvil]

It should hold a rotor just fine, holds everything else but I could get some pics of my other various loaders in the short cup for you guys.

grovy.. works for me. I'll take a 1" one I'm thinking... I like the look of the low profile. It holds a rotor properly right?

can/do you have a dust black one?

DM

[Nobody]

just remember, this is the guy that not only does fabulous work, but will treat your guns better than his own. if you have an Xmag, and want something that can clamp, then save up, contact BigEvil and take care that you will get what you are asking for.

[Dark Side]

Been meaning to get mine to you for years now. I'll have to PM you a question concerning ano.

[flampaint]

sending PM

[Mole1119]

PM sent