KAM Designs M86 Run #3

[cougar20th]

Messages sent to those with outstanding deposits.

[cougar20th]

Frames have shipped to me.
I have tracking numbers

Ill look them over and get them off to anodize. After they get here.

[alpha_q_up23]

Ahhhh Yeahhhhh!!!

[cougar20th]

I have frames

now its gonna take me a little bit to get these ready to be sent out again for ano. I have to separate them by finish.

Raw ones can go out shortly if those people would like.

[mobsterboy]

Yaaaaaasssss!!!!

[luke]

Hey Cougar, I'm starting to get questions about the using the P90 LPR on your frame, can you answer a few dimension questions?

Unfortunately it does not look like the KAM86 will be a candidate for the P90 LPR..

[cougar20th]

Hey Cougar, I'm starting to get questions about the using the P90 LPR on your frame, can you answer a few dimension questions? Thanks.

(click picture to enlarge)
[ATTACH=CONFIG]95725[/ATTACH]

Ill check tomorrow when I get to the office

[cougar20th]

To give you guys alittle idea of what I am up against.

This is the box of frames, panels, triggers.....All 35 pounds of them.
The box originally held a wheel for a car to give a idea of size.

To top that off I had some family stuff come up that I had to take care of.

[mobsterboy]

Family comes first!

:secretly hoping that if left in a box together, the frames might multiply :

[Loguzzzzzz]

I guess it is a good thing that there PLENTY other LPRs to chose from

[luke]

I guess it is a good thing that there PLENTY other LPRs to chose from

Doesn't change the fact that people are asking.

[Loguzzzzzz]

Doesn't change the fact that people are asking.

Not trying to change ANY facts just merely pointing out that there are many MANY other options. Why would anyone make a part that appears to only fit your LPR when you utilize and o-ring to seal and the 99.99% of other LPRs use a tapered pipe thread? Seems like a limiting factor to me. That is of course your LPR uses a 1/8" -27 straight cut thread instead of a tapered thread. Which admittedly I don't know.

[luke]

Not trying to change ANY facts just merely pointing out that there are many MANY other options.

Yes everyone knows that in this day and age, so all your SA comment did was muck-up Cougars thread.

Why would anyone make a part that appears to only fit your LPR when you utilize and o-ring to seal and the 99.99% of other LPRs use a tapered pipe thread? Seems like a limiting factor to me. That is of course your LPR uses a 1/8" -27 straight cut thread instead of a tapered thread. Which admittedly I don't know.

You're making assumptions here, the P90 is an 1/8-27 NPT thread which is a standard 1/8" tapered pipe thread, it's just a shortened thread that does not rely on the taper to lock the part down. It will work in all 1/8" NPT threaded holes same as any other LPR, if there's not a flat surface to seal on, you simply use thread sealer. Besides, I've planned from the beginning to make a standard fitting for those applications where a full 1/8-27 NPT thread is more viable.



BTW, as I understand it Keith utilizes a 1/8-27 straight thread in his frames so they can be threaded from the bottom instead of threading from the top down.

Cougar, I apologize for this nonsense...

[mobsterboy]

Not trying to change ANY facts just merely pointing out that there are many MANY other options. Why would anyone make a part that appears to only fit your LPR when you utilize and o-ring to seal and the 99.99% of other LPRs use a tapered pipe thread? Seems like a limiting factor to me. That is of course your LPR uses a 1/8" -27 straight cut thread instead of a tapered thread. Which admittedly I don't know.

Hey nerds, take it somewhere else. We have a paintball talk section of the forum for just this reason.

[luke]

Hey nerds, take it somewhere else. We have a paintball talk section of the forum for just this reason.

Easy fella, my original post was on topic, I got sucked into the nonsense...