RKM 3D Designs Presents the Troll, With special thanks to KAM Designs & Dirge.
This has been in the works for a few years now, but I finally got these off to be made. What you are looking at here is a simple design to utilize an LPR that already exist to power your pneumatics.
I Have These In Hand This Is Not A Pre-Order
Price is 150$ + shipping.
Payment method: Paypal.
Post in thread before PMing.
Trolls
Black Troll, with black anodized New Straight from PPS( Palmer's Pursuit Shop), Palmer's LPR
Shipping:
Small flat rate box through USPS, comes with 50$ of insurance if you would like more let me know and I will give you a new cost total
people outside the USA will need to give me your address so i can calculate a new shipping cost as it will most likely be higher.
Specs:
-RT Pro Flat Top Mounting surface with 2 holes 10-32 thread, Top and Side port hole for LPR routing choices (LPR Hose can either be routed out the side to the frame or completely concealed in the rail if lpr hose milling is performed)
-Left Hand and Right hand High Pressure Input Ports (1/8th NPT) for Ambidextrous hose routing, or if needed you could plug one hole and put a T fitting and run lines on one side of the marker.
-For demonstration/sale purposes, a Palmers LPR has been chosen since they are one of the strongest if not strongest manufacture in aftermarket regulators.
The Troll Package includes:
1x - Troll
1x- Palmers LPR
1x- 1/8” x 10-32 ss set screw
1x- straight brass barb with washer seal
2x mounting screws
20190425_185046.jpg
Troll Covers:
Currently not available + shipping
they fit as shown in the pictures below, shown with 3D Printed Prototypes.
Some pictures. ill get more pictures if needed( just ask).
20190226_204053.jpg
20190226_204057.jpg
20190411_203330.jpg
20190411_203335.jpg
20190411_203354.jpg
example of airline milling to run airline through rail.
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
20190411_203427.jpg
20190411_224821.jpg
20190411_225010.jpg
20190413_225616.jpg
20190413_225435.jpg
Shooting Videdo
this has my very first Troll setup on it. and has a custom 3D printed grip over the LPR, something I'm messing with and looking into.
if you need another video explaining anything just let me know ill get something put together. or you can pm and ill walk you through any questions you may have.
Any question don’t hesitate to ask.
This has been in the works for a few years now, but I finally got these off to be made. What you are looking at here is a simple design to utilize an LPR that already exist to power your pneumatics.
I Have These In Hand This Is Not A Pre-Order
Price is 150$ + shipping.
Payment method: Paypal.
Post in thread before PMing.
Trolls
Black Troll, with black anodized New Straight from PPS( Palmer's Pursuit Shop), Palmer's LPR
Shipping:
Small flat rate box through USPS, comes with 50$ of insurance if you would like more let me know and I will give you a new cost total
people outside the USA will need to give me your address so i can calculate a new shipping cost as it will most likely be higher.
Specs:
-RT Pro Flat Top Mounting surface with 2 holes 10-32 thread, Top and Side port hole for LPR routing choices (LPR Hose can either be routed out the side to the frame or completely concealed in the rail if lpr hose milling is performed)
-Left Hand and Right hand High Pressure Input Ports (1/8th NPT) for Ambidextrous hose routing, or if needed you could plug one hole and put a T fitting and run lines on one side of the marker.
-For demonstration/sale purposes, a Palmers LPR has been chosen since they are one of the strongest if not strongest manufacture in aftermarket regulators.
The Troll Package includes:
1x - Troll
1x- Palmers LPR
1x- 1/8” x 10-32 ss set screw
1x- straight brass barb with washer seal
2x mounting screws
20190425_185046.jpg
Troll Covers:
Currently not available + shipping
they fit as shown in the pictures below, shown with 3D Printed Prototypes.
Some pictures. ill get more pictures if needed( just ask).
20190226_204053.jpg
20190226_204057.jpg
20190411_203330.jpg
20190411_203335.jpg
20190411_203354.jpg
example of airline milling to run airline through rail.
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
20190411_203427.jpg
20190411_224821.jpg
20190411_225010.jpg
20190413_225616.jpg
20190413_225435.jpg
Shooting Videdo
this has my very first Troll setup on it. and has a custom 3D printed grip over the LPR, something I'm messing with and looking into.
if you need another video explaining anything just let me know ill get something put together. or you can pm and ill walk you through any questions you may have.
Any question don’t hesitate to ask.
Comment