Predator II Board - Authorized Install Center

[CoolHand]

That's right, we are now offering the Predator Morlock board for installation in several popular markers.

.................................................. .....................
Specs:
.................................................. .....................

Monolithic design - Ultra-high quality components used, Professionally assembled in an automated facility, and individually tested to the highest standards in a fully ESD-protected Mil-Spec environment.

Trigger sampled asynchronously - The predator does not "sample" the trigger as other boards do. The instant the trigger is depressed the board detects it - nothing is faster.

Power - The predator has a resistance of just .031 ohms. That is less than the copper wire used in any gun.

Current carrying capacity - The Predator can source up to 30 volts at a whopping 37 amps (that's over 1000 watts of power), combined with the near-zero on resistance. Its no wonder the predator can slam a solenoid open faster than any other board. If the wires were thick enough, the predator could start your bling bling sized urban assault vehicle.

Size - fits anywhere, smallest part count of any comparable board but packed with more features, lightest board around.

Upgradeable - as small as it is, it can be reprogrammed at the factory with any new features.

Computer Interface - will interface with a PC for fine-tuning of programming (existing board support it, interface cable/software coming soon)

Fire Timings - The Predator II has 18 different internal fire timings for a given rate of fire, which it selects based on 9 separate triggers. These are auto-selected on ashot-by-shot basis to make sure the next shot comes out as fast as possible and un-chopped.

Design and Engineering By KM2 - These are the guys that installed eyes in the Angel over 5 years ago and their technology is still being used in almost all of the super-guns on the market.

.................................................. ....................
Feature List:
.................................................. ....................
New board with Anti Chop eyes installed (break beam)9 volt battery operation. (includes a new plain ND eye cover)
Accessory Port for driving a hopper.
MROF is unlimited.
Factory support with Free software upgrades for as long as you own the gun.
Multiple firing modes (semi, full auto, auto response, 2 shot and 3 shot burst - Predator II only)
AFA Code (New Predator II Only) - Basically a ramping mode that kicks in after your programed ROF is reached (anywhere from 2-40 bps), when active, it drops the debounce after the programed ROF is reached, adding shots until the loader is maxed out.
X-Code - (Code name for NXL mode) - First 4 shots in the string are semi-auto, on the 5th shot, hold the trigger down and you get full auto at 15.75 BPS. Let the trigger go for 1 sec, and the cycle will reset.

.................................................. ....................
Prices:

Vision Impulse - $275
Non-Vision Impulse - $325
Shocker SFT - $350
EMag (Break Beam Eyes - ULE Bodies only) - $425 (They are a real bugger)
EMag (No Eyes - ULE or SS bodies) - $250
XMag - $275 (using ACE only)
HyperMag (Install Eyes) - $425
HyperMag (No Eyes) - $250
Viking w/o Eyes - $350
Viking w/ Eyes - $250
Intimidators - $250
Angels - $350

DIY Kit (board and standard install kit only) - $150 (No returns and no tech help on the DIY installs.)

.................................................. .................................................. ...........................

.................................................. .................................................. ...........................
Impulse Combo Deal - Pred II + Ripper V-2 Vert Frame - $375 Installed + Shipping
.................................................. .................................................. ...........................

.................................................. .................................................. ...........................
Shocker Combo Deal - Pred II + Ripper V-S Vert Frame - $450 Installed + Shipping
.................................................. .................................................. ...........................


***The Preds are back in stock now.***

*Above prices DO NOT include shipping.*

Thanks for stopping by.

[pulserifle99]

i know you said ule boddie, but are you able to install on a karta body?

[CoolHand]

i know you said ule boddie, but are you able to install on a karta body?

Yup. By ULE I meant anything except a stainless twistlock body. That means no classic bodies, rt bodies, minimag bodies, or older RTP/EMag bodies. Since the breech (where the sensors need to go) is part of the barrel, its a no go.

I can install these in any aluminum main body, be it a ULE, Karta, Dallara, Micromag, XMag, SFL, IT, etc.

Thank you for your interest.

[cognomen]

Sweet.

[02vertcocker]

Will installing this in an imp use the vision, or will it have a custom breakbeam setup?

[CoolHand]

Will installing this in an imp use the vision, or will it have a custom breakbeam setup?

Doesn't use the SP eye at all. You will get all new break beam eyes installed, with a new cover on the driver's side.

Hope that answers your question.

[02vertcocker]

Nice, and when you say vision imps, you just mean the new 2k2+ ones that are already drilled for an eye, right?

[CoolHand]

Nice, and when you say vision imps, you just mean the new 2k2+ ones that are already drilled for an eye, right?

Nah, its mostly to cover whether you will need one or two new eye covers. Machine work is machine work, regardless if the SP hole is there or not. That's all.

[Chris Nearchos]

where can i buy?

i`ve been looking and looking but i cant find a place to buy predator 2 board`s. where can i buy them at? i looking to have one for my project gun.
thanks,
chris

[CoolHand]

i`ve been looking and looking but i cant find a place to buy predator 2 board`s. where can i buy them at? i looking to have one for my project gun.
thanks,
chris

That's because they are not sold retail to the general public.

If you want one, you'll have to have it installed by one of the authorized install centers.

Sorry, but this had to be done, due to the number of people who would buy the board, botch the install, and then send it in for warranty repair (when there wasn't anything wrong with the board to begin with).

Thank you for your interest.

[LudavicoSoldier]

ARRRRGH! I am extremely competent with electronics and I was about to buy a Pred2 board to install in my LED angel. DAMN IT! I see no reason why someone who knows what there doing shouldnt be able to save some money and do it themselves!

Looks like im going to have to go with the Mini-Morlock with Predator code.

[Chris Nearchos]

pred 2 borad

okay, then may i ask if there is any way to buy the board WITH OUT the warranty?
thanks,
chris

[CoolHand]

Look guys, its not my call.

If it was just me, anything that showed up that I didn't install, would just be neatly repackaged, and sent back to the person COD for the shipping costs, but its not my call.

TAG warranties the boards, and my installs (he won't have to, but you get the idea). He can't tell whether a dealer botched the install or the customer, and he's getting overwhelmed. The easy fix is just to not let the dealers sell the boards alone. Then if it comes in all mangled, he can pin the blame on the dealer that butchered the job, or at least call and verify that it was right when it left (meaning the customer mangled it after the fact). These boards are basically bullet proof, if installed properly to begin with.

As with so many things, the stupidest amongst us has ruined it for the rest.

I'm very sorry, but its just not my call.

Thank you for your interest.

[Chris Nearchos]

pred 2 borad

so what your saying is even though i have a gun all ready to just drop the board in (a $150 board). iam going to have to pay you or some other dealer $350 just to drop the board in? (iam not angry with you in anyway just to let you know, so please dont take this personaly. just at the stupid people that made this happen.)
thanks,
chris
- oh, and is there any way to buy the board from the company? i mean that, that way they know what iam doing. so that if there was a problem that they know to point the finger at me and say that it was my fault?

[Richter]

Will you do hyperframes for predator installs? Yes there is dealer for this work but i have yet to see anyone else but the dealer have a board installed.

Also i see TAG does a magnetic trigger mod to the angels; do you do the same?

I have a hypermag and a angel lcd i would like to installs for.
send me an email ([email protected]) i perfer to discuss this in email vs your public thread here in automags.org