*** Fireblade Customs ***

[RRfireblade]

After the novel of work I wrote requesting last night, I may have him booked for a month or so


Styg

No doubt ..... I'm still reading it.

[StygShore]

last gun

Last gun I ever plan on owning unless technology drastically changes and it wont work anymore!! Might as well personalize it and make it my own, completely distinguishable from anyone elses.

Was thinking.... red Lexan sheets inside the battery pack, and mill through the outside of the pack? Would that be possible you think, or not enough room in the battery pack for the Lexan?


Styg

[RRfireblade]

I belive there would be some room for a thin sheet.

[StygShore]

hmmmm

That opens things up to some other alternatives if PK can not do the graphics for me....


Styg

[stoupa]

micromag body

Hi, Jay, how much would you charge for machining a custom rightfeed Micromag body?

[RRfireblade]

Depends on exactly what you want done. Shoot me an email with some details.

Thanks.

[Chaos_Theory!]

How much would it cost to have a battery housing with a design milled into it? I want the AO honey comb logo milled into both sides of one.

[sean33]

RRfireblade: Nice work. You recently did a fantastic job on my SFL clamping feedtube. Now i'm looking for some milling/custom work.

• Front End milled down
• Trigger Guard milling(front and rear)
• Trigger frame bumps
• Dovetail style gripframe
• Custom Trigger

Here is a rough sketch of my idea.



PM me the price when you have the time.

-Rob

NICE! can you tell me how much for that exact trigger? same color cuz my x-mag is black and that would look really nice... can you also respond via PM? thx good work

[psychowarden]

How much are you charging for the X-mag clamping feedneck mod. Is it only with CCM feednecks, or can we choose a different type? And what threads do you tap the breech for?

Thanks, and keep up the good work.

[spacedtedybear]

Can you make delrin bolt pins for AKA markers?

[SpitFire1299]

Email sent!

[dj89]

How much are you charging for the X-mag clamping feedneck mod. Is it only with CCM feednecks, or can we choose a different type? And what threads do you tap the breech for?


Thanks, and keep up the good work.

He dose not make any threads, but it may be able to use another feedneck, but it would need to be a mid or high rise.

[personman]

I hate to bother you/clutter up your thread but you didnt respond to my email and I'm a little worried now. Did you even get my ygrip? I havent heard a single thing from you since you told me to send it to you..
A little update would be nice
Thanks
Adam

[RRfireblade]

I hate to bother you/clutter up your thread but you didnt respond to my email and I'm a little worried now. Did you even get my ygrip? I havent heard a single thing from you since you told me to send it to you..
A little update would be nice
Thanks
Adam

Yes I did recieve it.

Here's an update for everyone along with an appology.

I just got back from out of state dealing with a family emergency which cost me at least a week worth of time on the machines.

In addition to that , I apparently way under estimated the demand for my services (pretty hard to complain about that tho huh. ) and have had WAY too much work show up. I've been trying to knock it out in the order in which work showed up on my door step but in a nut shell , that ain't cutting it by a long shot. So....

I'm behind......a tad.

This week I will do my best to catch up and get everyone back on track. If I haven't yet (there are like 200+) responded to your email I will in the next day or so and get everyone an update and ETA on thier work , to the best of my ability.

Again , I appologize. I just didn't prepare properly for the amount of work I took in and will not let that happen again.


Lastly ,

Until I get caught up and post so here , I'm going to hold off on any more incoming work.

Thanks for all your patience and understanding.

Jay.

Fireblade Customs.

[personman]

In that case, I'm sorry to hear that and I hope everything is okay.