KAM Designs M86 Run #2

[SoulCoffin]

Pm'ed you on beo

And happy bday

[Chrome]

Thanks for the info! I just took a ruler to the frames I have, and here is what I found:

AGD CF frame (and the metal frames just like it): 1/2" thick, 1-1/8" with stock plastic grip panels, 1-1/2" at widest with AGD rubber grips.

AGD ULE Emag frame: 3/4" thick, 1-1/8" with either stock or old style Luke's aluminum panels.

Dye 45 single trigger frame: 3/4" thick, no panels to test with.

So, unless you're going to build up some fairly thick rubber grips or something, panel grips on a 1/2" frame is going to be REALLY svelte. Looks like the overall average ends up being just over an inch however you want to divide it up.

[river031403]

Does anybody have a completed sleeper set up on these yet? Pictures?

[cougar20th]

Does anybody have a completed sleeper set up on these yet? Pictures?

Let me me cut up one this weekend. Then ill moint everything. It wont be functional. I dont have asa and wont be cutting my fabco.

[Chrome]

Sorry if I'm just not remembering seeing it in the original thread, but I read that the frame can take emag magnets above the trigger. Does the included trigger have a magnet (or a place for one) in it, or would that be something that would have to happen custom from somewhere else?

Also, I'm kind of thinking about getting in on this order. I really have no need/interest in a pneu setup. Could a frame be made without the sear release hole drilled? Would just be another place to have to dig paint/dirt out of at some point with it being there.

[cougar20th]

Sorry if I'm just not remembering seeing it in the original thread, but I read that the frame can take emag magnets above the trigger. Does the included trigger have a magnet (or a place for one) in it, or would that be something that would have to happen custom from somewhere else?

Also, I'm kind of thinking about getting in on this order. I really have no need/interest in a pneu setup. Could a frame be made without the sear release hole drilled? Would just be another place to have to dig paint/dirt out of at some point with it being there.

The frames will accept emag magnets. They are not included.

All frames come with the sear releas hole. To make it otherwise means custom and more cost. The hole is pretty handy on non pnue setups. I know one of my valves has a sticky on,off so otherwise i would hsve to remove the body to get the valve out.

[cougar20th]

Ok spent alittle time doing something painfull. Cutting one of the frames I was going to keep for myself. I had no intention of modding it but felt you all needed a real demonstration of how to modify these for sleeper mods.

Place fabco switch in the upper two mounting holes. Mark frame at bottom of the switch. Remove the switch and cut along the line & the back edge of the cavity. Removing the lower mounting screw. File slowly until lpr clears.
I did this using nothing more then a hacksaw blade and a file.


Tickler mounted and fabco mounted. You will have to cut the arm of the fabco down as nessesary. I did not as those parts belong on my M90 gun. You may also need to flip the arm on the fabco so that the air inlets are on the top with 90 degree fittings. Youll have to play some to find the exact setup.

[BigEvil]

FYI - you guys should realize that if Cougar20th says it's going to fit, it's going to fit !!

[cougar20th]

FYI - you guys should realize that if Cougar20th says it's going to fit, it's going to fit !!

I understand a rendering only goes so far to make people comfortable so I am also willing to cut up perfectly good product to make sure everyone is happy.

[rschoi_75]

Hey Keith,
I'll take the last spot. I'm sure I'll get around to using this one too.

[hawaiianking]

Ill take one.

[knownothingmags]

I understand a rendering only goes so far to make people comfortable so I am also willing to cut up perfectly good product to make sure everyone is happy.

should have had me print it
considering the cost that it has costed you
facepalm

[blamtro]

Pming

[cougar20th]

Im not going to be limiting the run. The preorder will be open until March 7. Which is what I originally put in the info. I never dreamed that it would hit the 10+ this fast otherwise I would have done shorter. But I feel it would be wrong to change the end time and possibly eliminate people.

[maverick13]

Good !

We're sure to get our frames !