EGOMAG Trouble, help please

[knownothingmags]

so i have my egomag setup put together.


GOOD:
-xvalve is tune and shoots fine.
-everything goes together just fine.
-using and EGO8 OLED board/the one that does the readout not the LED lights
-got a plug to plug the SMC noid into the board

BAD:
-SMC noid seems to be venting all the the time
-sometimes the ram in the clippard rammer stays out and does not reset
-the ram when it does reset and i start cycling shots with the ram in my hand, it doesnt seem to be activating very hard. (exmaple i get the lpr to put out a higher preasure and hold my thumb over the ram and it doesnt even move my thumb) is this right?, the hole time the smc noid is just dumping air out the vent port.

anyone who can help me with what to do please speak up.

thankyou for any and all help.
kinda bummed that this is not going well.

lmk what you guys think.

thankyou,
KNM.

[need4reebs]

wat psi is the lpr putting out???

[knownothingmags]

wat psi is the lpr putting out???

definently not the max for the noid

if anyone is wondering which one im using here it is.

http://www.airsoldier.com/mm5/merchant.mvc?Screen=PROD&Store_Code=AOS&Product_Code=SMC-S070C-SDG-32&Category_Code=SOLENOIDS

the tiny one but i have definently not over preasurized it.

[need4reebs]

maybe the lpr spiked causing the noid to leak...do you have a lpr tester to see what the pressure the lpr is putting when you air the marker up, shooting the marker, and when you de-gas the marker? the lpr could be spiking on ya???

[knownothingmags]

maybe the lpr spiked causing the noid to leak...do you have a lpr tester to see what the pressure the lpr is putting when you air the marker up, shooting the marker, and when you de-gas the marker? the lpr could be spiking on ya???

i dont think it is.
using a micro rock, or a tickler.

[need4reebs]

u got a pic of it? hoping its not a tickler lpr...they are great for a pneumag but i wouldnt trust them with a ep set up! i use a Micro Rock on mine and have a LPR tester so if the egomag has been sitting for awhile i can test the LPR and make sure its still set correctly! the Micro Rock is consistent as well as reliable but i would rather check the pressure to be safe than mess up my noid and have it start venting like the problem yours is having...them noids aint cheap!

[hill160881]

sounds like you have the air lines reversed. Double check you have the input, out and vent correct.

[knownothingmags]

sounds like you have the air lines reversed. Double check you have the input, out and vent correct.

yeah have the noid hooked up the right way with hoses and such.

[knownothingmags]

u got a pic of it? hoping its not a tickler lpr...they are great for a pneumag but i wouldnt trust them with a ep set up! i use a Micro Rock on mine and have a LPR tester so if the egomag has been sitting for awhile i can test the LPR and make sure its still set correctly! the Micro Rock is consistent as well as reliable but i would rather check the pressure to be safe than mess up my noid and have it start venting like the problem yours is having...them noids aint cheap!

i know i have six of them.

dont have ****ing air though so now im sol till tommorow.

[knownothingmags]

just so im not being a total bonehead,
counter clockwise or backing the adjuster out is lowering the lpr's preasure correcct?

[knownothingmags]

if its not a broken noid/ psi spike what else could be wrong?

[knownothingmags]

u got a pic of it? hoping its not a tickler lpr...they are great for a pneumag but i wouldnt trust them with a ep set up! i use a Micro Rock on mine and have a LPR tester so if the egomag has been sitting for awhile i can test the LPR and make sure its still set correctly! the Micro Rock is consistent as well as reliable but i would rather check the pressure to be safe than mess up my noid and have it start venting like the problem yours is having...them noids aint cheap!

i have a microrock that was reanodized,

i have a pebble pps lpr ill try when i get air along with a new noid.

[need4reebs]

if its not a broken noid/ psi spike what else could be wrong?

dont really know, any pics?

[knownothingmags]

dont really know, any pics?

how about this maybe this will shed some light.


maybe answer my issues with this build.

[hill160881]

I have only had one of these noids go out on me. It was due to a massive pressure spike. I blew my LPR and.........