** Official Level 10 Problems Thread **

[Cthulhu]

I have a silver, gold (shortest) and red spring... it doesn't work on any of the springs.

Thnx for the suggestion.. next?

[Plazmic]

Originally posted by Cthulhu
My understanding is I need a new reg piston, is that correct? Is it old enough to have "The old reg piston"?

I don't know enough about the older RT to know for sure, but it sure sounds like you need a higher pressure reg piston. That would be my recommendation at this point. You might go ahead and call up AGD and ask them if your older RT has the older reg piston. They'll give you the definite scoop.

[craltal]

I tried reinstalling my level X from scratch and still couldn't get it to stop that little leak out the back end so I put a new HP reg in the AIR valve and that solved my problem. Old valve I guess.

thanks.

[jesseyo13]

Hello everyone,
I put in my level 10 this saterday and it acts kinda wierd. Here are my problems.

1. After about 500 shots its started making a extremly small leak down the barrel, I think that it needs one more shim but I thought that I would ask first.

2. All the balls curve to the right. It may have something to do with the leak, I dont really know though.

3. The range seems to have droped by about 50 feet or so. I am shooting it at about 260fps.

4. While its leaking if I turn on the safty and pull the trigger it stops leaking.

Any help would be great guys

[Plazmic]

It sounds to me like your on/off is leaking. Try pulling the on/off, oilingit up a bit, and then putting it back. Make sure you get it in all the way. See if that doesn't help a bit.

[ChucktheMAGician]

jesseyo13 1. sounds like your powertube o-ring is getting broke in. Try the next smaller carrier using the same o-ring, the white one. 2. bad paint, bad paint to barrel match, and/or low velocity?

[jesseyo13]

Thanks guys, Ill try all of your sugestions

[ClouD]

chrono your fps to 285-300. i think that'll help a little.

[jdaniels]

velocity

i have to use my stock spring on my mag or the velocity is too high and it will start to vent out the back. I read that i may need a new reg piston or something. I have a classic valve and i dont have any leaks as of yet but i am worried about my velociy. Not chronoed it yet, i dont have one at my house. but i have shot it next to another gun that i know is right and my mag shoots a little hot. i hope the solution is cheap. Also what will cutting one of the new springs solve, is that another problem.

thanks
jonathan

[slade]

heres my problem, not exactly sure what is causing it, bolt or other: http://www.automags.org/forums/showt...hreadid=132989

[Darkknightheven]

Hi Guys, SOrry if this question gets asks constantly, but theres a lot of pages that i'd have to go through to find the solution to my problem!...Ok, i've installed my lvl 10 and when i gas up the mag it starts leaking where the velocity adjustment is at...What should i do???

[Plazmic]

DarkKnightHeaven, you need a new reg piston. You can order it from the AGD website. It pretty cheap, like $10 or sometihng like that. It's a higher pressure piston than the original and will not vent as quickly.

[Plazmic]

Slade, I posted in your other thread.

I think you just need to move your Level 10 carrier o-ring to the next smaller carrier.

[slade]

thanks, plazmic! it worked. i would never have thought that the problem would just be that the gun is breaking in. i dont have any leaking now... although the trigger bounce dropped, and i cant sweet spot nearly as well any more... oh well, id rather have a working gun without trigger bounce than a leaking gun with it. thanks for the help.

[Plazmic]

My Pleasure. Actually, the o-ring should break in just alittle bit more and you'll get some of that bounce back.