Clearance issues, help!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Cornmuffin87
    Proud Pumper
    • Aug 2002
    • 60

    #1

    Clearance issues, help!

    i need to find this out as quick as possible cuz i gotta order my christmas stuff....will a full sized shocktech drop forward clear my 6-stage ACI x-chamber? i want to be able to run the gas through the xchamber, but in order for it to fit will i need a stubby? or will the full sized one fit? (yeah yeah i realize my mag is running off of co2, so shadap and stop laughing)
    -Acid Grey VSC/RF 45 phantom
    JJ edge kit
    Punishers Ghost ring
    AGD Micro CA 2

    -Old style PGP pbmaxxed out
    rear velocity adjuster
    Vertical adapter
    Valve job
    Barrel hone
    quick strip
    milled ball slots
    palmers detent
  • Load SM5
    Scruffy Administrator

    • Oct 2000
    • 6772

    #2
    The full sized one might hit actually. I'd try the medium length.


    Moorewatch

    If you read this, thank a teacher.
    If you read this in English, thank a soldier.

    Comment

    • Cornmuffin87
      Proud Pumper
      • Aug 2002
      • 60

      #3
      mkay thanx! oh, and if anyone has a pic of their gun with either sized shocktech drop on it, i would like to see it (u dont need to have the xchamber) i just wanna see how far it will bring my tank down and forward. Thanx again!
      -Acid Grey VSC/RF 45 phantom
      JJ edge kit
      Punishers Ghost ring
      AGD Micro CA 2

      -Old style PGP pbmaxxed out
      rear velocity adjuster
      Vertical adapter
      Valve job
      Barrel hone
      quick strip
      milled ball slots
      palmers detent

      Comment

      • BeerCitySk8brds
        N2K
        • Jan 2002
        • 214

        #4
        Here is close up. Really old bad pic. It has Shocktech Medium.
        Feedback:
        http://www.automags.org/forums/showt...65#post1456865
        http://www.pbnation.com/showthread.p...29#post9567429

        PBNation: Bikeboardsnow
        PBReview: ihatespyders
        AIM: Bikeboardsnow


        E-Mag
        ULE
        3.2 Software
        Fireblade
        Progressive Barrel

        Comment

        • Cornmuffin87
          Proud Pumper
          • Aug 2002
          • 60

          #5
          thanx!
          -Acid Grey VSC/RF 45 phantom
          JJ edge kit
          Punishers Ghost ring
          AGD Micro CA 2

          -Old style PGP pbmaxxed out
          rear velocity adjuster
          Vertical adapter
          Valve job
          Barrel hone
          quick strip
          milled ball slots
          palmers detent

          Comment

          • anthraxxx
            Registered User
            • Dec 2001
            • 85

            #6
            i have a full sized ST drop and it hit my 4 stage aci. I just switched to a standard sized kapp foregrip and that hit as well. if you want the bottle as far forward as possible you will need to use the full size drop. just put a spacer between the grip frame and drop, about 1/4 or an inch thick and that should allow you to clear the x-chamber or foregrip. only thing is you will have to be creative on the hose fittings if you want to run it through the foregrip/x-chamber, it going to be one tightest set ups for hoses around.

            good luck

            Comment

            • Cornmuffin87
              Proud Pumper
              • Aug 2002
              • 60

              #7
              thanx! and when beer mentioned the 'medium' sized drop, is that the same as the 'stubby'? cuz on www.paintballgear.com all they have is a' Shocktech Dropforward" a "Shocktech minidrop" and a "Shocktech stubby" so is the stubby the medium one? cuz i might sacrifice more drop and forward for an easier fit, or i may go with the spacer idea. ugh! wish i had nitro so i could just run it up to the reg and get a 'dead on' dropforward.
              -Acid Grey VSC/RF 45 phantom
              JJ edge kit
              Punishers Ghost ring
              AGD Micro CA 2

              -Old style PGP pbmaxxed out
              rear velocity adjuster
              Vertical adapter
              Valve job
              Barrel hone
              quick strip
              milled ball slots
              palmers detent

              Comment

              • BeerCitySk8brds
                N2K
                • Jan 2002
                • 214

                #8
                I'm not sure i know there is small (inch or 2, medium (4 inches), large (5 inches) I would assume stubby is the medium one but im not positive.
                Feedback:
                http://www.automags.org/forums/showt...65#post1456865
                http://www.pbnation.com/showthread.p...29#post9567429

                PBNation: Bikeboardsnow
                PBReview: ihatespyders
                AIM: Bikeboardsnow


                E-Mag
                ULE
                3.2 Software
                Fireblade
                Progressive Barrel

                Comment

                • Load SM5
                  Scruffy Administrator

                  • Oct 2000
                  • 6772

                  #9
                  There is the Shocktech Long -4" or so
                  Shocktech Stumpy which is the medium - about 3/4"-1" shorter that the Long
                  and the Mini-which goes about 1 1/2" forward and is slightly angled.

                  I personally love the mini and have used all 3.



                  Moorewatch

                  If you read this, thank a teacher.
                  If you read this in English, thank a soldier.

                  Comment

                  • Cornmuffin87
                    Proud Pumper
                    • Aug 2002
                    • 60

                    #10
                    thanx a lot guys! i think im gonna go with the medium one, i should be able to clear it with that!
                    -Acid Grey VSC/RF 45 phantom
                    JJ edge kit
                    Punishers Ghost ring
                    AGD Micro CA 2

                    -Old style PGP pbmaxxed out
                    rear velocity adjuster
                    Vertical adapter
                    Valve job
                    Barrel hone
                    quick strip
                    milled ball slots
                    palmers detent

                    Comment

                    Working...