i need to find this out as quick as possible cuz i gotta order my christmas stuff....will a full sized shocktech drop forward clear my 6-stage ACI x-chamber? i want to be able to run the gas through the xchamber, but in order for it to fit will i need a stubby? or will the full sized one fit? (yeah yeah i realize my mag is running off of co2, so shadap and stop laughing)
Clearance issues, help!
Collapse
X
-
Clearance issues, help!
-Acid Grey VSC/RF 45 phantom
JJ edge kit
Punishers Ghost ring
AGD Micro CA 2
-Old style PGP pbmaxxed out
rear velocity adjuster
Vertical adapter
Valve job
Barrel hone
quick strip
milled ball slots
palmers detentTags: None -
The full sized one might hit actually. I'd try the medium length. -
mkay thanx! oh, and if anyone has a pic of their gun with either sized shocktech drop on it, i would like to see it (u dont need to have the xchamber) i just wanna see how far it will bring my tank down and forward. Thanx again!-Acid Grey VSC/RF 45 phantom
JJ edge kit
Punishers Ghost ring
AGD Micro CA 2
-Old style PGP pbmaxxed out
rear velocity adjuster
Vertical adapter
Valve job
Barrel hone
quick strip
milled ball slots
palmers detentComment
-
Here is close up. Really old bad pic. It has Shocktech Medium.Feedback:
http://www.automags.org/forums/showt...65#post1456865
http://www.pbnation.com/showthread.p...29#post9567429
PBNation: Bikeboardsnow
PBReview: ihatespyders
AIM: Bikeboardsnow
E-Mag
ULE
3.2 Software
Fireblade
Progressive BarrelComment
-
thanx!-Acid Grey VSC/RF 45 phantom
JJ edge kit
Punishers Ghost ring
AGD Micro CA 2
-Old style PGP pbmaxxed out
rear velocity adjuster
Vertical adapter
Valve job
Barrel hone
quick strip
milled ball slots
palmers detentComment
-
i have a full sized ST drop and it hit my 4 stage aci. I just switched to a standard sized kapp foregrip and that hit as well. if you want the bottle as far forward as possible you will need to use the full size drop. just put a spacer between the grip frame and drop, about 1/4 or an inch thick and that should allow you to clear the x-chamber or foregrip. only thing is you will have to be creative on the hose fittings if you want to run it through the foregrip/x-chamber, it going to be one tightest set ups for hoses around.
good luckComment
-
thanx! and when beer mentioned the 'medium' sized drop, is that the same as the 'stubby'? cuz on www.paintballgear.com all they have is a' Shocktech Dropforward" a "Shocktech minidrop" and a "Shocktech stubby" so is the stubby the medium one? cuz i might sacrifice more drop and forward for an easier fit, or i may go with the spacer idea. ugh! wish i had nitro so i could just run it up to the reg and get a 'dead on' dropforward.-Acid Grey VSC/RF 45 phantom
JJ edge kit
Punishers Ghost ring
AGD Micro CA 2
-Old style PGP pbmaxxed out
rear velocity adjuster
Vertical adapter
Valve job
Barrel hone
quick strip
milled ball slots
palmers detentComment
-
I'm not sure i know there is small (inch or 2, medium (4 inches), large (5 inches) I would assume stubby is the medium one but im not positive.Feedback:
http://www.automags.org/forums/showt...65#post1456865
http://www.pbnation.com/showthread.p...29#post9567429
PBNation: Bikeboardsnow
PBReview: ihatespyders
AIM: Bikeboardsnow
E-Mag
ULE
3.2 Software
Fireblade
Progressive BarrelComment
-
There is the Shocktech Long -4" or so
Shocktech Stumpy which is the medium - about 3/4"-1" shorter that the Long
and the Mini-which goes about 1 1/2" forward and is slightly angled.
I personally love the mini and have used all 3.
Comment
-
thanx a lot guys! i think im gonna go with the medium one, i should be able to clear it with that!-Acid Grey VSC/RF 45 phantom
JJ edge kit
Punishers Ghost ring
AGD Micro CA 2
-Old style PGP pbmaxxed out
rear velocity adjuster
Vertical adapter
Valve job
Barrel hone
quick strip
milled ball slots
palmers detentComment

Comment