I want to find out where most people run their retro valves and such with their tanks. When you state what your input pressure is, also state how it works their and what kind of ROF you can get. Thanks for any replies.
-
Minimag
retro valve w/lvl 10
Y-grip
warpfeed(12v x-board feeding it)
centerflag preset(subject to change) -
my gun is sick my out put pressure is between 600 and 1000 and it dose auto at its slowest at 15 or 20 and fastest in the 30's -
Sorry bud thats not possible to get 30 on a mag. The xvalve can only cycle 26 times a second. So how do you expect us to believe that you can get in the 30's, even when pros cant get near that.Originally posted by AGD Paint Baller
fastest in the 30'sHey, look at that! It's Santa!
Comment
-
yeah 30 is way to high. 13 bps is faster then a lot of people think.
i run a classic w/ lx, stock trigger and crossfire preset tank.
i get a good 5 to 6 balls average 7 on adrenaline.
it may be little bit but my markers got no kick back at all.mag for now, mag foreverComment
-
The xvalve has been tested AT MOST at 26 bps. AGD hasnt been able to test it faster than that, but noone has said it wont work at 30 bps. And I think he's talking about sweetspotting the trigger. Doing that can get some mad bps, although 30 sounds a little high.Originally posted by WenULiVeUdiE
Sorry bud thats not possible to get 30 on a mag. The xvalve can only cycle 26 times a second. So how do you expect us to believe that you can get in the 30's, even when pros cant get near that.Comment
-
BPS
Actually, as I understand it, the X-Valve has been tested at 26 BPS with no shootdown. It will actually go higher but you may experience some shootdown.
B-)Bryan
Phantom Regiment
Team Mag Daddies
CPPA Member
Sponsored by Paintball Quest
Primary Marker: Black Alias
Secondary Marker: XSF SpyderMag
X-Valved (of course) with Level X and ULT
Black Center Feed ULE with Halo B
Logic milled rail, Evil Pipe kit
68/4500 CrossFire @ 850 PSIComment
-
^ Iwas sort of thinking about that when I typed my first post. But no one can even pull 26 a second, I doubt pros can, and that means you especially cant AGD Paintballer.Hey, look at that! It's Santa!
Comment
-
-
o yeah and by the way if you remove a o-ring it goes full auto or u can sweet spot it to do sick rof'sComment
-
I am sure who ever was pulling was extremely expeieneced and that wasnt you so yea. And for all you know he did remove the oring to acheive such a high BPS. But the fast is anything over 20 bps is rediculousy(sp?) fast.Hey, look at that! It's Santa!
Comment
-
i did the same thing he did remove the on/off top o-ring and crank the pressure it dose it all the same as himComment
-
but whats the point of argueing about weather i can or cant do 30 bps it its was just a question about how fast the valves could do at what pressure and it dose go over 26 w/o shut downComment
-
The RT valve has been tested up to 26 bps without shoot down. That only means that its guaranteed to bee 100% consistant up to 26 bps. It doesnt mean you cant shoot faster. As a matter of fact, there is a clip around here (ask JAck&Coke) of an automag (mech) doing 33. Tony is right.(nya, nya
)
Although speeds that fast rely heavily on runaway or trigger bounce.
Anyways...
I ran my Xvalve at 800. I know for a fact that I could get like 16 at least. (I could outrun my revvy with ease, and it was intellifed. The level 10 kicked in every few shots when I really tried to rip on it.)
In a game, tho, I never wanted to go that high.
Team Sandbaggers.
-We own j00 all.-Comment
-
I dont know. Lets stop before it gets out of hand.Originally posted by AGD Paint Baller
but whats the point of argueing
-AndrewHey, look at that! It's Santa!
Comment
-
lol good ideaComment
Comment