IntelliFeed help with Warp and Hoppers - Rob?

[davisdawg123]

give agd a ring, they are extremely helpful

[MagNumPI]

Question on the switch

The switch gets activated when the sear hit it right? Is the sear in the intelliframe different then that of the stock frame?

If not can I have a picture of the inteliframe sear.. I'm trying something with my mag that involves the same idea..

[n1mr0d]

Re: Question on the switch

Originally posted by MagNumPI
The switch gets activated when the sear hit it right? Is the sear in the intelliframe different then that of the stock frame?

If not can I have a picture of the inteliframe sear.. I'm trying something with my mag that involves the same idea..

the intelliframe doesn't have a diff sear, just a little bracket for mounting a roller switch right at the pivot of the sear. so when the sear moves back, it hits the roller switch. plus the intelli has a little plug already milled into the body.

[MagNumPI]

ok , so basicly anyone thats technicaly inclined can make this style of hopper.. i'm gonna buy the parts and make it tonight on my stock frame. TIME TO TAKE OUT THE TRUSTY DREMEL (Ever notice that dremel andpaintball go hand in hand... wonder if the ever approached dremel to make a specific model for paintball?)

[n1mr0d]

Originally posted by MagNumPI
ok , so basicly anyone thats technicaly inclined can make this style of hopper.. i'm gonna buy the parts and make it tonight on my stock frame. TIME TO TAKE OUT THE TRUSTY DREMEL (Ever notice that dremel andpaintball go hand in hand... wonder if the ever approached dremel to make a specific model for paintball?)

that's the atituide bro.....i should see if i can mount one on my benchy....it's alredy got a trigger stop adjustment hole in the back....wait....damn can't use that i'll have to make another hole.

[MagNumPI]

Make a hole in your grips not the frame..i'm probably gonna have to do both since they are complete cover grips.



Has anyone ever considered a air powered hopper.. the kind you put a 12g co2 caplete in? I might look into it.. Damn I feal creative..

[ah137]

Re: warp, rev,& emag on same battery...

Originally posted by Butch Borsic
I've just finished the connections to my emag. everything is working good, except that my warp runs about 2-3 times as fast as it did before is this a potential problem or is it normal. all my connections to the warp and rev have the 9v connecters that plug in to the loaders circuits.

the voltage of the emag battery is like 16.8 volts, which is almost twice of the normal voltage of a 9 volt battery, if you switch between the 4 AA and the 9 volts you can notice the difference there too. So the more volts the faster it will feed, I believe the warp can handle up to 12volts, So you will have to regulate it down. You might have to adjust the dewel time so it don't over spin so much.

later Hills

[unseenunheard]

boo-yahh frames

has anyone ever tried to do intelli with a boo-yahh frame and if so, does the switch inside the frame give enough voltage to flip the warp on or should i run this to a solenoid and let this engage the warp.

[Chef123161]

Re: Re: warp, rev,& emag on same battery...

Originally posted by ah137

...I believe the warp can handle up to 18volts

The warp can SAFELY handle 12 volts. You will need to regulate the voltage down to at least 12. Check out Robs other post on how to do this. Good luck.

[kilaueakid]

I didn't see in Rob's write up how he got the 16.8 volts from the emag battery down to under 12 volts for the warp feed? Where does he explain this? I will check again though. Anyone else know?

[headcase]

Rob mentions using a resistor to bring the voltage down, only problem is he couldn't remember what size resister. I posed this question at the Tinker's guild and got the following replies:

http://www.network54.com/Hide/Forum/message?forumid=9013&messageid=1006972310

that link will bring you to my original messge, just keep following the follow ups, and all your questions should be answered.

Later
SSDD

[SGTKennedy]

i would like a spring loaded magazine 10 rnd tube modified, and have a modified JT speed collar mounted under and parallel to the barrel so the "hopper" was a 100 rnd tube that could be exchanged when it ran out.
Just have to figure out how to make a quick switch so that a full tube could be put under while the empty(s) could reload. maybe 3 10rnds hanging down with springs and some sort of air assist reload to change tubes and pack the springs for gravity feeding.
pointless with warpfeed out there. but itd make a great afternoon in the machine shop. and would stick out on the field. put it on a stingray.
Kennedy

[PowderdToastMan]

Is the intellifeed really worth buying? it seems like a lot of work......

[Stimpy]

great pic...

[Hunter Predd]

ok besides hooking up to the revolution and teh warp feed what else does the intellifeed do? (this is probably a stupid question to u guys, and i know it)