tac one not fast enough

[Recon by Fire]

Note, the ULT does decrease reactivity when set up correctly. Stuffing as many shims as possible into it is not removing the reactivity! When the bolt is broken in and you have everything set up good, it will rip. Dump that girly man tank and get a HP adjustable. MAX-FLOW! :)

[coofoo777]

i got the tac one off special ops paintball. cool gun. comes pertty well loaded. But I can not get it to shoot like in the level ten videos. I would like at least a three round burst. I added shims to the ult. doses the same thing as when i got the gun. I changed carriers and the springs. I just want to shot fast. WHAT do i do,anybody! Also talk in simple terms i am new to the game.

Im not an expert, but I think the level ten bolt vid was with
a deadlywind trigger. Does ne one know when or where the deadlywind trigger is done?
or if it was just done on that one gun or wat?

[onedude36]

I have an adjustable armageddon tank i may be selling soon. Its at hydro right now.

[11 Bravo]

how about this from a mag owner, i have a hyperframe on my mag and it still isnt that fast. So take my advice sell the tac and get an ion or an a5 w/ an e grip.

Then you obviously dont know how to set up a mag. Dont put down the guns just because you dont know how to set them up.
I have a two Hypermags and I took the time to set them up right. They rip, and I would put them up against any marker out there. As a matter of fact they are faster than my Angel 05 speed (at its current settings).

[rb211]

Well put 11 Bravo!! Dont give up on the gun because you can't shoot 26bps like the valve is capable of doing. Set it up and break it in. And most importantly, learn the gun. I'm certainly no pro, but once I really learned mine, I can rip it like there's no tomorrow just by walking or sweetspotting the trigger. I have not tested it for how many BPS it is slinging, and really dont care - that's not the way I play the game. I do however like it when someone wrongfully accuses my gun of being a shocker because of some of the rates of fire I have acheived with it.

[Dayspring]

Just an FYI, if the gun is shooting 1 ball per pull, then the gun is working correctly. Multiple balls per pull or bouncing is NOT.

Yes, it's fun, but not correct.

Pull the trigger faster.

[StellarRAD]

i got the tac one off special ops paintball. cool gun. comes pertty well loaded. But I can not get it to shoot like in the level ten videos. I would like at least a three round burst. I added shims to the ult. doses the same thing as when i got the gun. I changed carriers and the springs. I just want to shot fast. WHAT do i do,anybody! Also talk in simple terms i am new to the game.

I'm still a little confused on what is really going wrong. You talked about only 1 ball per pull, but are you wanting a reactive trigger/bounce?

What happens when you walk the trigger?
How quick do you think you can get it firing?

I have a fully tricked out E-mag with X/valve and ULT and I run around 8-12pbs. Learn to snap shoot and MOVE on the field. I rip DM4-5s and may other 20+bps guns apart.

To many people have purchased guns for the spray and prey, but it's so much fun to piss them off tearing them up with something that does half of what they throw.

[Geoff Call]

I fully agree with most parties here on these facts:
-Tank output is over 800ish.
-On/Off pin is shorter than stock.
-O-rings have been worn in well.(shooting at least 10 cases of paint through a mag will do wonders. And don't cheat by dry-firing because you'll shoot off your foamie.)

-OIL
-OIL.
-OIL!

My personal preference is the stock on/off assembly because if the above aspects are tuned correctly your trigger pull will be fairly light, you will RT on command, you can more than likely walk the trigger quite easily, and you will overwhelm your opponent with a whirlwind of paint.

My on/off pin was custom shortend by my colleague at work. I told him to make it "controllably fast" and in doing so my marker RT's an easy 20 bps and I can single shot just as easily.

Quad O-rings are a neat trick as well. I have 3 in my valve and everything is like butter:) Look into it.

If your mag doesn't RT, you aren't shooting enough paint through it and oiling it enough!

-Geoff Call

[blamtro]

Quad O-rings are a neat trick as well. I have 3 in my valve and everything is like butter:) Look into it.

What is the quad oring trick?

[Castro #66]

You could always get emag lowers for you Tac-One. Like mine, for instance. I have a Tac-One as well, and am looking to get the ULT'd Intelliframe. If you trade me, I'll give you a $150 discount, costing you only 150, and you would then have a mech/electro switchable with 3 and 6 round bursts. Also has a Fireblade LT-3 trigger. Let me know by PM if you're interested.

[Geoff Call]

What is the quad oring trick?

Quad o-rings shown here can be placed in the on/off assembly to replace the smaller o-ring inside. They are made to have less resistance than the regular o-rings and thats why they are standard in the e-mags and x-mags. It just so happens that there are 2 other places to put these o-rings in the valve offering very little resistance on the smaller moving parts in a mag. At least that is my understanding of it all. Enjoy.

-Geoff Call

[11 Bravo]

Just make sure that you are putting more than 800 psi into the gun and then adjust the shims in your ult. You will have to find the right # of shims and once you do it will rip like you want. Just have patience and find the right settings.