how to get R/T or bounce effect for a

[FOG]

Classic mag , all stock with a single trigger , is it just putting in a x valve and putting 900 plus psi into the valve, or is there more to it ? Thanks

[Mongoose]

any rt valve will do...
x-valve is just lighter

[FOG]

and is that all ? no trigger change or anything? and THANK YOU for the reply.

[snoopay700]

It can be done with a single trigger, it's just harder. If you get in intelliframe it should be easier.

[phizz]

I thought the X valve was a bit harder to get the counce off of for some reason... Not sure why I think this.

Don't get the ULT

[snoopay700]

I thought the X valve was a bit harder to get the counce off of for some reason... Not sure why I think this.

Don't get the ULT

An x-valve is the same as my classic rt valve in function (the x-valve is lighter and the on/off is milled differently so it can accept the ult). Now from what i've heard the ULT makes it harder to bounce, unless you pack it full of shims.

[FOG]

OK , X valve and a crossfire tank w/ a good adj. reg goes on my xmas list, and then on my mag,

Thanks evryone, and any other advise you have is welcome and appreciated!

[warbeak2099]

OK , X valve and a crossfire tank w/ a good adj. reg goes on my xmas list, and then on my mag,

Thanks evryone, and any other advise you have is welcome and appreciated!

Any variant of the RT valve will work:

RT Pro
Retro
Emag
X
Micro RT
Micro E 2000
Emag Xtreme
etc.

Also, a double trigger will allow more leverage and easier sweet-spotting.

[FOG]

WARBREAK,that was a concern w/ my single trigger, (the sweet spot that is)
hmmm maybe i,ll wait on the double trigger an see how hard it is to swwet spot w/ the single

[magmonkey]

it is harder to get an x valve to bounce. I belive agd changed the on/off pin length specificly to get rid of the potential for bouncing

[FOG]

HMMMMMM opinions on MAGS post please.
( x valves are harder to get to bounce ? )

[mostpeople]

Dont think so...


X-valve broken in with ULT and a garaunteed 850 psi input and there is no trouble for either me or nu_metal

(you saw us riding our ULT's at OCP right?)

[FOG]

MOST ,yep i sure did

I keep hearing that a ult isnt as good for Bounce as a none ult.
I did find that i have a ans venturi bolt. Doing a lil research on it peeps either like or hate it

Opinions ???

[Danterwhoo]

MOST ,yep i sure did

I keep hearing that a ult isnt as good for Bounce as a none ult.
I did find that i have a ans venturi bolt. Doing a lil research on it peeps either like or hate it

Opinions ???

Well I can't get my normal ON/OFF to bounce at all with the X valve, I just can't get it to go. But the ULT bounces like crazy!! But everyone says that the regular ON/OFF bounces better but I can't bounce it once (and thats with a 1025 psi tank).

[maniacmechanic]

Opinion's ; everybody has one & thier just about all different
From what I learned when I met you at OCP this will work for you & be easier on the pocket ; R/T Pro valve , level X , & a intelliframe . Shop around Christmas is a long way off , mabey wait till after when folk's have to pay them Christmas bills and are sellin off stuff they been hoarding
As others have said the valves are nearly the same , most of the R/T effect comes from tuning & pressure , a 2 finger trigger is easier to rt than a single (IMHO)
I've got a R/T Pro valve with a r/t on/off that rips , I've got 2 X's that rip with ULT's in them but a diff # of shims , both my E-Mag valves go good on the mech side with the battery off