E-Mag Owners!!! ACE Board Upgrades!

[KC]

Luke and Evade are working with My-SFL to get milling set up at lukes customs.

I will be sending an emag off to mill at XT next week sometime.

This will solidify and refine the milling service and prices associated.

[KC]

BUMP for more votes.

Come on emag owners, VOTE!

[211]

so what Im reading, this wouldnt work with a twistlock body, unless the barrel was also drilled to allow the ACE to see into the breech

[KC]

so what Im reading, this wouldnt work with a twistlock body, unless the barrel was also drilled to allow the ACE to see into the breech

Correct, just send the barrel in with the other parts.

[evade]

Correct, just send the barrel in with the other parts.

would the eye protrude into the outer diameter of the barrel at all? If it does it might be difficult to twist.

[KC]

would the eye protrude into the outer diameter of the barrel at all? If it does it might be difficult to twist.

EDIT: The eye can read far enough away that it shouldnt be an issue. The ace eye would just have to be installed lower... I dont know exactly how we are going to handle it, but It shouldnt be an issue.

[vikking_1]

i would love an on/off switch as i have misplaced my pin and havent found it yet. if i could have just an on/off and my board with xmod i would be happy.

[KC]

i would love an on/off switch as i have misplaced my pin and havent found it yet. if i could have just an on/off and my board with xmod i would be happy.

You wouldnt save much with just an on/off, better to just spring for the ace board. imo.

[KC]

SO we only have about 55 emag owners here on ao?

please vote...

[MANN]

SO we only have about 55 emag owners here on ao?

please vote...

sounds about right. Each of us just own a half dozen

[Dark Side]

Any possibility on getting a warped Emag with eyes? I just can't let go of my Warp.

[KC]

Any possibility on getting a warped Emag with eyes? I just can't let go of my Warp.

Sure, why not? The warp body is no different then the other ULE bodies. The milling work wouldn't be any different.

[KC]

Big Update

Im sure most of you understand what this thread was hinting at. We have enough inplace now that Papa_Smurf and I would like to announce we will be selling E-Mag ACE board upgrades soon. X-Mag & SFL ace board replacements will aslo be available.

Looper has agreed to make signal wire kits for us. more details soon.

Next week we will be sending an emag off to XT along with a New ACE Board and my own X-Mag. This step will provide XT will the info he needs to mill the bodies, rails and frames.

Once we have the emag back in our hands we will make any corrections, if needed, and
the milling service though XT will "go live."

At that point a thread will be setup in the dealer section to begin the pre-sale of Ace Board replacements as well as E-mag upgrade kits.

Please post any questions you might have.

-Kristian

[Ruler_Mark]

Joy!,, mabey you should look into some rubber gromets to cover the hole where the switch is and all raw metal caused by this. so that we wouldnt have to get the guns re-annoed.

[Empyreal Rogue]

I'm anxious to see before/after pictures. I've seen some ACE work on E-Mags with little slots milled into rails, but I never understood the purpose since X-Mags didn't have it. I always thought the design behind the ACE allowed all the milling to be inside the rail/body/frame so that nothing showed on the outside, gave everything a more seamless look, which is the exact route I'm taking with my E-Mag project.

Is it for the on/off switch? If so, couldn't that be re-routed someway? Couldn't it be possible to take advantage of the hole in the battery pack, thread it and insert a toggle switch or pressure button? That would certainly make the overall price a bit more expensive but would be a nice option, even if we have to buy the button/switch and re-wire the whole thing ourselves.

Thoughts, opinions?