Sniper Breach Mods

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • p8ntbal4me
    No more UTBs!
    • Aug 2003
    • 2560

    #16
    Look up the Tagline TS-1 (now called the ATS TS-1)

    Thats a magazine fed marker,..... and if correctly done with the magazine,.. you could get it to work (but the gun itself sucks!)

    That SMG would be a PRIME candidate!

    ~ P8nt
    _______________________
    Jai "P8ntbal4me" Menard

    Comment

    • Ninjeff
      it only takes one.
      • Jan 2007
      • 1205

      #17
      Revolver.

      Someone just needs to make some type of rifle-esq revolver.

      Heck, i want a paintball revolver anyway.
      Doesnt seem like it would be that hard.....

      Or, someone could widen a warp feed, turn it side-ways and have them feed like an off set drum magazine.

      Or, perhaps the easiest, is figure out a way to use the Tibireus clips on a mag, maybe using a power feed cut out to accept the rounds with an additional piece that "latches" in the clip.

      Comment

      • Swamp Thing
        Registered User

        • Dec 2007
        • 356

        #18
        Alternative

        I wonder is one of the markers that may also handle this might not be the Q loader SSI. I have not looked but if is bottom fed straight up into the gun. I think if you take the Q socket off you may find that a bolt on magazine may be possible to construct.

        Swamp

        Comment

        • zondo
          One of 8 bosses... again.

          • Dec 2006
          • 2245

          #19
          Couldn't you just use a piece like a carrier in pump action shotguns? This would lend itself to using the longbow type system so no change in designing a shaped magazine, but it would still need a different style feed hole.
          Stay Classy, AO...
          BEO: RIP / Topgun Paintball: RIP / Old MCB: RIP

          Comment

          • Hilltop Customs
            Registered User
            • Aug 2007
            • 1260

            #20
            Originally posted by zondo
            Couldn't you just use a piece like a carrier in pump action shotguns? This would lend itself to using the longbow type system so no change in designing a shaped magazine, but it would still need a different style feed hole.
            Because of the hollow backside of the rounds, it would be pretty complicated to load them with that type of system. The tail would fall into the breach, but the nose would still be contained in the backside of the next round. To use that type of system you would have to hold the next shot in place while separating and loading the current round. The shotgun/longbow type of feed was the first thing that popped into my mind too, but unfortunately, I think it would be pretty complicated loading them in that style. If you reverse it and have the rounds come from the rear of the marker it opens up a few more options, but it would still be a pretty complicated loading operation.

            Comment

            • zondo
              One of 8 bosses... again.

              • Dec 2006
              • 2245

              #21
              Originally posted by Hilltop Customs
              Because of the hollow backside of the rounds, it would be pretty complicated to load them with that type of system. The tail would fall into the breach, but the nose would still be contained in the backside of the next round. To use that type of system you would have to hold the next shot in place while separating and loading the current round. The shotgun/longbow type of feed was the first thing that popped into my mind too, but unfortunately, I think it would be pretty complicated loading them in that style. If you reverse it and have the rounds come from the rear of the marker it opens up a few more options, but it would still be a pretty complicated loading operation.
              You and your feed systems...
              Stay Classy, AO...
              BEO: RIP / Topgun Paintball: RIP / Old MCB: RIP

              Comment

              • doc_Zox
                Team Dead by Dawn
                • Jun 2003
                • 723

                #22
                Tom Kaye already figured out the reliable way to feed these rounds:

                Comment

                • MANN
                  I am in TN. GO VOLS.
                  • Apr 2006
                  • 4266

                  #23
                  Originally posted by doc_Zox
                  Tom Kaye already figured out the reliable way to feed these rounds:
                  but I want one that can put out 13.3 bps. Not cause I need it, but cause I want one.

                  Comment

                  • michbich
                    machinist-biochemist
                    • Jul 2007
                    • 849

                    #24
                    Originally posted by MANN
                    but I want one that can put out 13.3 bps. Not cause I need it, but cause I want one.
                    You mean 13,3$ps.

                    Comment

                    • notcreative
                      Registered User
                      • Feb 2004
                      • 451

                      #25
                      Think of the possibilities cutting up a nerve.

                      Comment

                      • skyless
                        Registered User
                        • Mar 2006
                        • 576

                        #26
                        Revamp the mag

                        It would be hard to convert a regular mag to use a barrel feed. Bummer that the grip frame is in the way for doing an under feed as well. maybe its time for someone to make a new grip/rail combo that allow for more options.

                        Mabie even make a rail that takes the FS clips and have an under feed and set back grip with sight mounts on the body, with option for a hopper as well. I was also thinking that if these rounds are longer then paintballs that the detents would get in the way as well so that has to be figured too.

                        On second thought, make better clips without having the air source in them.
                        Last edited by skyless; 02-17-2009, 02:01 AM.

                        Comment

                        • ultralight
                          Tool Weilding Ape
                          • Feb 2005
                          • 770

                          #27
                          can someone show me where it says that these are longer than a paintball?

                          If i remember correctly, they are the same length, just a square back side instead of round. I know somebody mic'd one, but i can't find the thread.

                          Comment

                          • Swamp Thing
                            Registered User

                            • Dec 2007
                            • 356

                            #28
                            I Want It All And I Want It Now

                            There is nothing that I would like to see more than for that FN 303 posted above to be translated into a marker that I can use Tomorrow but barring info that this is in the works I need to figure how to use my current markers with the First Strike Rounds

                            Swamp

                            Comment

                            • hitech
                              Not a shedder of vortices
                              • Nov 2001
                              • 4775

                              #29
                              Originally posted by ultralight
                              can someone show me where it says that these are longer than a paintball?

                              If i remember correctly, they are the same length, just a square back side instead of round. I know somebody mic'd one, but i can't find the thread.

                              Originally posted by smoothice
                              What are the measurements of these rounds from tip to tail?

                              Originally posted by manike
                              0.686"

                              But you have to remember that in side profile the back is square which means they can't drop into the breech of a normal gun in the orientation required for them to be fired.

                              It's kind of like a square plug won't go into a round hole.

                              As for the other dimensional discussions, they appear to be almost identical to my FN303 rounds for the base dimensions, but the tails on several of the FS rounds are oval (I suspect not on purpose but due to the manufacturing with such a thin wall) and this means that the dimensions can be larger or smaller than the equator depending on how you measure them.

                              Mine are all around 0.686 at the equator too.

                              Unfortunately this means they don't fit into my glass barrel which is 0.68
                              There you go...



                              Hey Hitech your starting to sound like me! - AGD
                              Hitech is the man.... :eek: - Blennidae
                              The only Hitech Lubricant

                              Comment

                              • skyless
                                Registered User
                                • Mar 2006
                                • 576

                                #30
                                opps

                                Guess i read that wrong, Cool. They look like they are longer but thanks for clearing that up.

                                Comment

                                Working...