Who is still rockin the warp?

[snoopay700]

The power feed - hopper right bodies always seemed like a good choice for warps or q-loaders to me. I'm a little surprised that there aren't more pics with them.

As far as the q-loader i can probably fill that, twist lock detents are weak, so weak that it is the only time my level 10 broke paint and got stuck forward. It being winter might not have helped, but i got rid of it as soon after that as i could, and at a loss too.

[Watcher]

As far as the q-loader i can probably fill that, twist lock detents are weak, so weak that it is the only time my level 10 broke paint and got stuck forward. It being winter might not have helped, but i got rid of it as soon after that as i could, and at a loss too.

I can see that, especially if the barrel is single detent. I know some field paint around me that will just roll out of my ACI barrel. More often than not I end up using the stock barrel.

[fishmishin]

I just picked up a warp setup for the ULE mag I picked up. I am looking forward to shooting some folks with it over the next two months in preperation for AO South.



Anyone else still shooting these?

I have to tell you, I love the way that marker looks set up the way it is. I keep going back to look at it every time I check this post. Had to quote ya on the 2nd page so I could look at it from here, and not go back to the 1st page, lol.

[pump]

I have to tell you, I love the way that marker looks set up the way it is. I keep going back to look at it every time I check this post. Had to quote ya on the 2nd page so I could look at it from here, and not go back to the 1st page, lol.

same here

im all up ons

[punkncat]

Aw, shucks guys.......



Thanks

[snoopay700]

I can see that, especially if the barrel is single detent. I know some field paint around me that will just roll out of my ACI barrel. More often than not I end up using the stock barrel.

Yeah i actually don't like the stock barrel on my RT so i end up using my crown point, it's probably something to do with the barrel tip or something. But because of that the q-loader was a mess for me.

[Enhander]

Still rocking the Warp! I love it!! Im currently switching between the warp and the Longbow setup on my Tac-One. When I get another Emag, ill put the Warp back on the Emag, but until now I switch between the 2

[Watcher]

Yeah i actually don't like the stock barrel on my RT so i end up using my crown point, it's probably something to do with the barrel tip or something. But because of that the q-loader was a mess for me.

I thought the RT stock barrel WAS a crown point, unless you mean the original one?

[snoopay700]

I thought the RT stock barrel WAS a crown point, unless you mean the original one?

No, it's not really a crown point, the original crown point had the barrel fade away (and do nothing) the RT barrel is the inverse of the crown point, and doesn't really look like a crown, but then again it's all semantics.

[Shirow]

So, FYI, anyone looking to warp feed a vert mag without a feedneck, PTP has the warp feed tubes that screw into an angel threaded body for $9.95, I just bought one. They come standard matte black. Nothing special, just a tube with angel threading on it but it seems to do the job

[Watcher]

So, FYI, anyone looking to warp feed a vert mag without a feedneck, PTP has the warp feed tubes that screw into an angel threaded body for $9.95, I just bought one. They come standard matte black. Nothing special, just a tube with angel threading on it but it seems to do the job

Or you can file off the clamp for the screw on the 90 degree elbow that comes with the warp, and stuff it IN any standard vert-feed.

The screw isn't needed to tighten anything down, even when it clamps around a feedneck it is snug as is...

[Shirow]

Or you can file off the clamp for the screw on the 90 degree elbow that comes with the warp, and stuff it IN any standard vert-feed.

The screw isn't needed to tighten anything down, even when it clamps around a feedneck it is snug as is...

Yeah, someone suggested that to me, I just decided I wanted to try to get rid of the feedneck.

[DoubleDutch]

I rocked the Warp last weekend at the "Wrath of Cobra Commander" Big Game at Dynamic Paintball in Aurora, CO. I was the only one, got a lot of questions.

[FutureMagOwner]

Probably just a halo remodeled with a mount and output hose right?

I know a few people working on those. I don't see any advantages over my warp, as my warp plus the Rico weight about as much as a stock ReloaderB...

Sorry, forgot to respond to this a while ago, I kinda forgot that I posted in this thread until now. It has similarities but its a different take on a hopper that I think people will hopefully want to buy. Right now I am waiting to save up some money to get a prototype made before moving on to developing a final product.

[druid]

I just got......THE BEST STOCK - EVER CREATED!!! Killjoy industries ROC Stock is THE absolute BOMB!

It came preassembled for me in the Left-hand configuration [at my request], with the small adapter plate installed. I ended up taking that one off in favor of the large plate. Installation is a snap and is actually ROCK SOLID in the receiver. There is ABSOLUTELY NO movement where it pins in place.

However...this thread's about the Warp so I warped my A5



Pics