Armada Bodies

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • luke
    lukescustoms.com

    • Jan 2001
    • 8211

    #46
    I sent PMs to everyone on the list, if you want to decline please let me know so I can make the body available to someone else. Thanks

    1. Gundam V (Slotted)
    2. Apathetic_Chaos (Slotted)
    3. going_home (No Slot)
    4. awo702 (Slotted)
    5. notoriousMAG (No Slot)
    6. Luke
    7. ikillforwork

    Armada Body Compare.jpg
    Last edited by luke; 02-24-2019, 09:16 AM.

    Comment

    • luke
      lukescustoms.com

      • Jan 2001
      • 8211

      #47
      Just a little teaser, slug body prototypes are done. All the math looks good but will need to test after the Armada machining is done. I'll start machining fixtures for the Armadas tomorrow..

      Slug BodyP1 A.JPG

      Slug BodyP1 B.JPG

      Comment

      • awo702
        Registered User

        • Aug 2015
        • 473

        #48

        Comment

        • luke
          lukescustoms.com

          • Jan 2001
          • 8211

          #49
          Here's how I'm dong the spring cup/retainer on the new slugs, I couldn't find the necessary tooling to do this on the Deflator bodies. These are easier to install and remove compared to the AGD version. The retainer clip lines up with the front edge of the sear slot so it's easy to get to with a pick.

          If you look closly you can see the retainer groove.
          Slug Body clip spring cup.JPG

          Single-Turn Spiral Internal Retaining Rings.
          These are common 'off the shelf' clips from McMaster Carr. These have a little hook on the end to aid in removal.
          clip and spring cup.JPG

          Comment

          • luke
            lukescustoms.com

            • Jan 2001
            • 8211

            #50
            The last Armada body is running on the mill now. I still have rails to make then everything needs to be ran through the deburr tank. I also need to test them to make sure were good to go. I wouldn't count on shipping until next week.
            As soon as this project is don I'll be doing a large run of slug bodies and more slug rails. I had a vision for the next body/rail so I'll start those as soon as I get through all the production.

            Thank you gentlemen.

            Comment

            • Apathetic_Chaos
              Registered User
              • Mar 2017
              • 229

              #51
              Originally posted by luke View Post
              The last Armada body is running on the mill now. I still have rails to make then everything needs to be ran through the deburr tank. I also need to test them to make sure were good to go. I wouldn't count on shipping until next week.
              As soon as this project is don I'll be doing a large run of slug bodies and more slug rails. I had a vision for the next body/rail so I'll start those as soon as I get through all the production.

              Thank you gentlemen.
              Sweetness

              Sent from my SM-G960U using Tapatalk

              Comment

              • awo702
                Registered User

                • Aug 2015
                • 473

                #52
                Originally posted by luke View Post
                I had a vision for the next body/rail so I'll start those as soon as I get through all the production.
                Oh, hells yeah.



                Sent from my iPhone using Tapatalk

                Comment

                • luke
                  lukescustoms.com

                  • Jan 2001
                  • 8211

                  #53
                  I'm excited to see what you guys do with your builds, I think this is the direction I'm going to go.

                  I've been looking for the right setup to do a gas through foregrip with panels.

                  Z grip Forgrip.JPG

                  Comment

                  • luke
                    lukescustoms.com

                    • Jan 2001
                    • 8211

                    #54
                    One body left, I believe there are two guys I haven't heard from yet that expressed interest.

                    Comment

                    • Apathetic_Chaos
                      Registered User
                      • Mar 2017
                      • 229

                      #55
                      Originally posted by luke View Post
                      I'm excited to see what you guys do with your builds, I think this is the direction I'm going to go.

                      I've been looking for the right setup to do a gas through foregrip with panels.

                      [ATTACH=CONFIG]100666[/ATTACH]
                      I say add finger grooves

                      Sent from my SM-G960U using Tapatalk

                      Comment

                      • luke
                        lukescustoms.com

                        • Jan 2001
                        • 8211

                        #56
                        Grooves may not be a bad idea, this is just a 2 minute concept drawing. The Z's just look bad IMO with little spindly foregrips. This one wouldn't be as wide or thick as a grip frame but big enough that it would feel substantial in your hand. It should be a perfect platform for a Sidekick, good stability for 'right hand free' ripping on the trigger.

                        Comment

                        • luke
                          lukescustoms.com

                          • Jan 2001
                          • 8211

                          #57
                          Oh yea, the forward position and the rounded area where the marker would rest between the thumb and pointer finger is just a guess, both would be adjusted for proper fit and feel.

                          Comment

                          • luke
                            lukescustoms.com

                            • Jan 2001
                            • 8211

                            #58
                            OK gentlemen bodies are ready to ship, I'll get them in the mail Monday morning.

                            Bodies will ship with the spring cups installed..

                            Thanks guys

                            Comment

                            • awo702
                              Registered User

                              • Aug 2015
                              • 473

                              #59
                              Originally posted by luke View Post
                              OK gentlemen bodies are ready to ship, I'll get them in the mail Monday morning.

                              Bodies will ship with the spring cups installed..

                              Thanks guys

                              Comment

                              • going_home
                                Hebrews 13:8

                                • Dec 2004
                                • 8343

                                #60
                                Got my tracking # .

                                Sooo who are you guys using for anodizing ?

                                Satin black will be close enough for my dust black Xvalve.






                                (who needs a preorder when things ship this fast !)

                                Comment

                                Working...