Electro Logic Vert Automag Frame????????

[sslecyk03]

dude thats the exact setup i want, right now i have rt pro with xvalve, ule, and ygrip, im gonna get a dallara, elogic, and then get a dust orange anno. Can u say pimp?

[speedyejl]

I'm telling you and before you send off to anno man you gotta get it drilled for EYES!!!!! It would take a 5min on any drill press and the eyes would cost all of $15 can you say hotness

[sslecyk03]

how bout pimp hotness, a WAS and ACE'd dallara body'd mag only shows up in my wildest dreams. Then i wake up and have to change my pants

[PaintballSmurf13]

that frame, was or morlock board, ace,lighter microswitch, V2 chord body, stiffi barrel and other stuff...ultra light,impossible to break paint,smallest profile, super sexy, that is my dream, now if you'll excuse me, i have to go change my pants now.
-Ryan F.

[SaS]

anyone tried mixing a ACE, or the like, with a hyperframe?

Unless the programing is setup for something like that i wouldn't think it could without some changes. But if it could, then wouldn't be too much work to do if you wanted, just go to a airsmith who can and good to go. Interesting idea.

[phantomhitman]

why would you need ace or eyes? i thought level 10 was good enough? i am asking, not telling so please do not take it that way.

[No Excuse]

Originally posted by phantomhitman
why would you need ace or eyes? i thought level 10 was good enough? i am asking, not telling so please do not take it that way.

When the lvl x tries to shoot and the ball isnt in the breech yet it "chuffs". This means one of your trigger pulls did not result in a ball fired. Chufing also puts some people of their firing rhythm.

The WAS (if i understand this right) will save up your shots so that if you fire and the ball isnt breached, it will wait untill the eye says it is and then fire. Im talking fractions of a second delay here so its not gonna fire when you dont want it to.


This would give u a few more bps maybe...

There are many more edvantages to the was system over the centerflag, such as debounce, more frequent trigger checking etc which all add up to make it the best board out at the moment.

[speedyejl]

Well said No Excuse,

I also would just like to add that you'll see many high end guns that mechanically prevent chops also do so electronically.

Examples Matrices, Xmag, Impulses

I know on my NYX I was using an EggII which I can easily outshoot. If I turned the eyes off I would end up shooting the same ball on the side almost 5times in some cases. While my NYX still bounced paint, the LX is a little rougher and if you nail a ball 5times in a row or more its gonna burst.

[Prezents]

$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$

Well we all wanted this to happen,
Coolhand said to me that he would not even start this project till he has 25 people that have made a deposite.
Well he has started, so we need to start.
I have sent him $$$ for my deposite.
It takes time and money to make this frame.
Prezents

[CoolHand]

Lets not go too far yet.

I can float this for a while yet, and I'd just as soon not take money for them yet, in case this whole deal goes south.

Not saying that its gonna, but just in case.

I'll start a preorder thread when I'm ready to collect up some money.

Thanks for the initiative though.

[BajaBoy]

coolhand, if this frame goes threw... you have my personal word.. im Selling the ace'd emag for this gun. Also you gotta make some Kickass triggers for it

[sslecyk03]

yes, please let this deal go through. And i know its hard to say at this point in the project but, if it goes through, approximately how long do u think it will be before u start to begin putting these out on the market. And have u talked with WAS yet?

[phantomhitman]

thanks for the info no excuse. coolhand, i can wait patiently.....but i do not know about a couple of ben franklins though i hope you the best on this project, because it will be a close race between me and prezents to see who gets one first

[CoolHand]

I have spoken to WAS, and they were amicable with the arrangement, so we will be moving forward with their board as the foremost choice.

I am still not 100% sure of which model we will be using, as space is a concern, as well as the question of whether or not they can even actuate that big solenoid.

Does anyone here know how many amps the CF solenoid draws when fired?

This will make a big difference as to whether we can use the WAS board or not.

I still don't have an estimated release date, as we are just begining the development process.

That's the latest.

[sslecyk03]

someone give him that info so we can speed up the process a bit.