can i put on this grip?

**MonsterMag** · 10-26-2004, 08:36 PM

Originally posted by master_alexander

i like the black one in the rotating pic, know where i can get it?

http://aimpaintball.com/products.asp

**personman** · 10-26-2004, 08:38 PM

Originally posted by master_alexander

i like the black one in the rotating pic, know where i can get it?

That's an autococker grip frame, I'm not sure why he posted it.

**MonsterMag** · 10-26-2004, 08:43 PM

Originally posted by personman

That's an autococker grip frame, I'm not sure why he posted it.

because , it also might work , never know

and it shows the sear

**master_alexander** · 10-26-2004, 08:45 PM

it does show the sear, but is it electronic?

**personman** · 10-26-2004, 08:56 PM

Originally posted by emagballa560

because , it also might work , never know

and it shows the sear

No, it wont work.
It will fit but it wont work, especially in electronic. You might be able to rig it up for mechanical pull but it will be tricky and probably not work all that well.

And no, its not electronic.

**Duzzy** · 10-26-2004, 10:33 PM

You do realize that you will be trying to get a blow back marker frame to work on a blow forward. Which means that you will have to mess with sears, God only knows if there is enough room in a E-Force fram for a mag sear, although maybe if you chop it down... You also have to have some strong enough to move the sear while keeping the pull "electronically" light. On a classic maybe, but without ULE I think an RT might be too heavy. I would get a used Hyperframe, that would be a little more expensive, but not only could you later make a DevilMag, but you also don't have to worry about modifiying the frame and messing it up and wasting your money. My 2 cents to your donation fund...

**SpecialBlend2786** · 10-26-2004, 11:11 PM

Not sure about the piranha frames, but I know that for the Spyder ESP frames you can flip the solenoid around. That way you dont have to modify your mag sear other than removing the trigger rod

**luke** · 10-27-2004, 08:08 AM

Originally posted by SpecialBlend2786

Not sure about the piranha frames, but I know that for the Spyder ESP frames you can flip the solenoid around. That way you dont have to modify your mag sear other than removing the trigger rod

SB2786,
Can you point me in a direction of someone that has done this mod? I just want to verify that it's mechanically compatible with a Mag.

I was thinking it would be cool to install the electronics in a Intel frame.

I would like to completely hide the fact that it's an electro...

**Mosfet** · 10-27-2004, 08:26 AM

Originally posted by luke

SB2786,
Can you point me in a direction of someone that has done this mod? I just want to verify that it's mechanically compatible with a Mag.

I was thinking it would be cool to install the electronics in a Intel frame.

I would like to completely hide the fact that it's an electro...

a good search usually works.
Thats how I found the info.

But to be helpfull... you don't use the eframes sear to replace the Mag's sear as I take it a few of you are thinking.

There are 2 ways to do this.

1. Remove the eframe's sear and have the solenoid directly trip the mag's sear
2. Modify the mag's sear so that the e frames solenoids trips the e-frame's sear, which then trips the mag's sear... but thats just a bit more complicated then it has to be.

As for sear tripping force, a classic and an RT should be about the same amount of force needed... which happens to be more than an eframe can handle. This is why the eMag had the huge battery.
You need to install a ULT on/off or a hyperframe on/off to lower the amount of force needed by the eframe to trip the sear.

heres how most people set up the solenoid / sear:

Solenoid = {] (Plunger hit to the left)

Sear =
____
|

Solenoid + Sear:
____
|{]

I hope that helps.
I myself will be doing an altogether different approach involving:
68 Classic Mag (no ult or lvl10)
Imp Frame (it was cheap)
Cocker LPR and Ram
Timmy SOB Board
Solenoid (still need to purchase)
That should make me a nice Electro-Pneumatic-Sear tripping Mag.

**Mosfet** · 10-27-2004, 08:30 AM

Here you go.
I found this in less time then it took to write the above post:

The SpyderMAG, Incl a How To - Automags.Org Online Forums

http://www.automags.org/forums/showthread.php?t=143273

Paintball Talk is the main forum for Automags.org. Here is where we talk about the sport of paintball in general and make announcements relating to the forum and website.

**luke** · 10-27-2004, 10:06 AM

Originally posted by Mosfet

Here you go.
I found this in less time then it took to write the above post:
http://www.automags.org/forums/showthread.php?t=143273

COOL!

Thanks Mosfet your the best!

**master_alexander** · 10-27-2004, 03:59 PM

i decided to put this stuff on it instead of the piranah frame

ANSgear.com - Not Found

http://www.pbreview.com/products/reviews/906/