Need beta testers for "stainless steel body Warp Feed (only) mod."

[vf-xx]

I'll bite, if you have a 90* warp adapter that I could purchase as well.

[luke]

You mean like what comes stock with your Warp?

[vf-xx]

You mean like what comes stock with your Warp?

Yeah, I need another one of those.

[behemoth]

I replied in the other thread that i'd test it for ya...


Just thought i'd hit here too

[luke]

Yeah, I need another one of those.

I probably have a few laying around, (I don't use them with this mod myself.) I'll throw it NC if you get the mod.

PM me if your intrested.

[luke]

I replied in the other thread that i'd test it for ya...


Just thought i'd hit here too

PMed you.....

[DiSoRdeR]

Do you have any pictures of the vert feed one? And would you happen to have any pictures of this done to a Minimag?

[luke]

Do you have any pictures of the vert feed one? And would you happen to have any pictures of this done to a Minimag?

The only picture I have is the one above. I haven't gone into full production with these; the pictures you see above are of the prototype. The Vert feed will go straight up from the existing hole one your gun body, so it will be slightly offset.


I've had lots of people say they were sending their bodies in for the mod, but I haven't received any yet. I will get pictures when given the opportunity.

I may even shoot a 30 second video of each mod in action. Can't promise when though. I have a pretty full plate right now. I have something else in the works today, may have pictures up tonight.

[danheneise]

i got mine back yesterday (monday) and it looks really REALLY clean and awsome, as soon as i opened it i ran up stairs and thew it on my gun and admired how nice it looked with the rest of my guns parts all put together. then i went to put the barrel in and had a problem , the barrel slid in like normal but stopped once it got half way past the feed tube, me being the idiot that i am pushed it into the carpet and forced the barrel on the rest of the way, well it looked great with it on and all but i thought that i might actually want to switch out my barrels sometime so i started pulling on it, and tugging on it, and yanking on it and it didn't budge. some how today i managed to get some strenght out of my scrawny little arms and yanked that baby out but now i've stupidly done the same thing again with my other barrel

another problem with it is that it dosen't sit in the rail properly, i've taken it on and off many times trying to get it to position riight but no mater what i try it lifts up in the back a little bit, and also pushes the valve up off of the rail. luckly i have a brand new minimag body that i just ordered so i'm not totally screwed. I think i'm going to try my dremel a bit in the inside of the body to see if i can't get the barrel to fit in any better...

[crackerjack]

danheneise
I did that to my old minimag body when i tried to weld the power feed tube back on the body after I broke it off. What happen was the metal got hotter on one side than the other and warpped the body. I tried to fix it by hammering the barrel in and heating the body with a torch.
That made it a little better but I trashed it and bought a ULE body. So in short that body is trash. I have a Emag/RTpro power feed hopper left body you can have for FREE + shipping if you what to try it again.
Jack

[luke]

i got mine back yesterday (monday) and it looks really REALLY clean and awsome, as soon as i opened it i ran up stairs and thew it on my gun and admired how nice it looked with the rest of my guns parts all put together. then i went to put the barrel in and had a problem , the barrel slid in like normal but stopped once it got half way past the feed tube, me being the idiot that i am pushed it into the carpet and forced the barrel on the rest of the way, well it looked great with it on and all but i thought that i might actually want to switch out my barrels sometime so i started pulling on it, and tugging on it, and yanking on it and it didn't budge. some how today i managed to get some strenght out of my scrawny little arms and yanked that baby out but now i've stupidly done the same thing again with my other barrel

another problem with it is that it dosen't sit in the rail properly, i've taken it on and off many times trying to get it to position riight but no mater what i try it lifts up in the back a little bit, and also pushes the valve up off of the rail. luckly i have a brand new minimag body that i just ordered so i'm not totally screwed. I think i'm going to try my dremel a bit in the inside of the body to see if i can't get the barrel to fit in any better...

Don't quit on me yet. The body was checked with a Stock RT Pro barrel and it worked fine here. I can fix it. Send the set up as it is, barrel, rail and the body. I'll make it right no charge.

Remember this is a beta..

[luke]

danheneise
I tried to fix it by hammering the barrel in and heating the body with a torch.
That made it a little better but I trashed it and bought a ULE body. Jack

Please do not try this.

I'm sure I can straighten out the problem.

By the way this work comes with a warranty. If a body is ruined it will be replaced.

[GT]

still need beta testers?

[luke]

Pmed you...

[danheneise]

sorry i'm taking so long in getting my body back to you for you to fix, i still want that done but it's gonna take a while as christmas has royally screwed my wallet over