Morlock Board Problems

[SpitFire1299]

Im trying to install my predator morlock board, and im having some problems. Its for my hyperframe.. for my automag. Im not using eyes, and im sure that all the wires are plugged in the correct places. The settings are at the default (I Think..). What happens is, I turn the board on, and i pull the trigger. The solenoid(For sure works..), doesnt click, and the light just flickers. Im thinking the eyes might be on, but i cant turn them off since all that happens when i hit the trigger is the light flickering.

Please Help!!

[mobsterboy]

yup its broken, sell it to me for close to nothing and cut your losses
really tho, email TAG, they'll help you out

[SpitFire1299]

I need this working for tommorrow though..

[mobsterboy]

why morlock if no eyes? Sure, speeds but thats about it

[SpitFire1299]

why morlock if no eyes? Sure, speeds but thats about it

Its better than the 13bps board, and i spent less than getting the 20bps. Im not going to sell this board either, I would really appreciate some help.

[mobsterboy]

do you have eyes available? If so, try connecting them and seeing if it fires

[SpitFire1299]

Sorry man.. I read that like 10 times and it still doesnt help me. I hold the trigger to turn the eyes off for 2 seconds, and all the light does is flicker. I tried 3 seconds, 4 seconds.. etc..

[SpitFire1299]

EDIT:

I hooked them up, and when i go to turn them off, it turns off. Then, it still acts the same.

[warbeak2099]

Contact TAG asap. Bob will be able to help you infinitely better than we. Chris at Devilsden, Ryan at Logic, or the boys at KM2 (http://www.exarin.com/) might also be good to contact.

[BigEvil]

Like I said to you on aim, I think you have a bad board.

They eyes will blink rapidly when they are 'off'


I think you need to get on the phone with TAG asap. They will know exactly whats up.

-Scott

[SpitFire1299]

Like I said to you on aim, I think you have a bad board.

They eyes will blink rapidly when they are 'off'


I think you need to get on the phone with TAG asap. They will know exactly whats up.

-Scott

Do you or anyone else have there phone number? I emailed them before, but no response yet.

[SpitFire1299]

..Does anyone know how to reset the board?

[CoolHand]

There is no "default" settings for a Morlock board in a hyperframe.

The settings that come on them stock will not work at all.

You need to change your settings to match these.

ROF to 25
Dwell to 25
Debounce to 25
Fire Hold off to 1
Eye Hold off to 1

You will need to check your manual to see what registers correspond to the above settings.

If the board lights up, it's not fried. I have never had a Pred that was bad light up, they generally do nothing at all.

Those settings should get you into the ball park.

Make sure you have a new battery in it, and that you are still using the big capacitor that was on the old board. Without it, all this is moot.

I would also suggest that you look for another marker to use in your tourney, just in case.

[mobsterboy]

haha, knew it would come in handy

Predator-Morlock
Operation, Functionality and Troubleshooting
LED:
Solid - ball in breech Blinking slow - breech clear Blinking fast - eyes disabled
Dip Switches:
Either or both switches in the ON position activates the tournament lock. You will not be able to go into program mode
unless BOTH switches are off.
Activation:
Switch on the power switch located on the gun
Eye Operation:
You can turn your eyes on and off by holding the trigger down for 2 seconds.
Wiring harness - Front, Writing Down (HKS) (wires pointing away)
1 = White (eye +5 volts at 150ma max) short lead
2 = Green (eye signal)
3 = Black (emitter -) short lead
4 = Orange (emitter +)
5 = Red (solenoid 2)
6 = Yellow (solenoid 2)
7 = Red (solenoid 1)
8 = Blue (solenoid 1)
9 = Black (battery -)
10 = Red (battery +)
11 = Black (trig -)
12 = Grey (trig +)
Example for programming your Predator:
1. Your tournament LOCK must be off if your board has that feature. We strongly suggest you turn your
tournament lock on while playing.
2. Pull and hold the trigger then turn the gun on by using the button on the back of the gun
3. Release trigger
4. You are now in the REGISTER select area
5. Pull trigger the appropriate number of times to go to register. Example: 2 pulls will take you to the MROF
register (register 2)
6. LED will flash the current setting of the register you selected
7. You are now in MODE select area
8. You can now pull the trigger to insert the new setting.
9. The LED will flash 2 times to indicate it has taken the new setting
10. You are now back in the REGISTER select area
11. You can now move to a new register by simple pulling the trigger the appropriate number of times or turn the
gun off and back on to use the new settings
NOTE: If you select Register 1, you are expected to enter a fire mode, again in trigger clicks. After you have made a
selection, the light will flash and remain on. The gun is now prepared to fire. We suggest you make the fire mode the last
register you select as the board will reboot after it has been selected.
Programming advanced firing mode example on Predator board:
Player wishes his or her marker to ramp once they reach 6 bps but NOT start ramping until they have fired 10 shots.
1. Go into programming mode by turning your board on while holding the trigger back
2. LED will flash once to indicate you are in program mode
3. Release the trigger
4. Pull trigger 5 times to enter the RAMPING ROF register (register 5)
5. LED will flash the current setting
6. Pull the trigger 6 times to set this register to 6bps
7. LED will flash 2 times to indicate it took the new setting
8. Pull trigger 6 times to enter the RAMPING SHOT COUNT register (register 6)
9. LED will flash the current setting
10. Pull the trigger 10 times to indicate you wish the ramping to start after you have fired 10 shots
11. LED will flash 2 times to indicate it took the new setting.
12. Pull trigger 1 time to enter the FIRING MODE register
13. LED will flash the current setting
14. Pull trigger 6 times to enter FAST RAMPING mode
15. LED will flash 2 times to indicate that it took the new setting AND the gun will reboot and be ready to fire. The
gun reboots automatically after you set register 1. This does not happen after any of the other registers.

[SpitFire1299]

Alright.. Ive got it working, but its in full auto mode.. It wont come out of it either.