The Rarest of ALL Mags ( I don't even have one)

[aqua_scummm]

ok no more jokes lets get rich.

Somebody find me a titanium valve

[FARMER00]

Hmmm. That's odd. My mag valve seems to weigh the same as a duck.

sadly not enough people will understand that



anyways, my cousin played way back in the day and he said he remembers the dude who sponcered them had the ti valve, now his field and proshop was burnt down (mafia related stuff) and i doubt he would still have it after that, but ill call him up and ask him about it (ive played a game or 2 with him, he doesnt play anymore) for ya tom

[back2integrity]

SO what are standard valves suposed to weigh? (and is that without the bolt and spring?)

*Bonus points for answering in grams*

12.7g w/ on/off and PT tip and Macro fitting (no bolt)

12.0g w/ on/off and tip (no bolt)

11.6g w/ PT tip but no on/off (and no bolt)

10.6g w/ no on/off or PT tip or bolt or nut (11.1g with nut)

[zorrotmm]

BURN IT!!!!

Wow, that was a lightning fast response with a screenshot! You gotta admit though, this is the closes thing I've seen to a mag inquisition.

For years to come mag valves may be scratched, ground and burned until the unorthadox alloys that hide among us are found

[aqua_scummm]

I keep special pics in my photobucket, you know, just in case

[Jimmykaboots]

Lol. Odometer is what's in your car. An Ohm-meter measure the resistance of a particular object.

Where the dunce am I gonna get an Ohm Meter? Its not like everyone has one lying around in their closet lol. *runs over to Canadian tire* Think the local hardware store will have an Ohm-meter?

[aqua_scummm]

Where the dunce am I gonna get an Ohm Meter? Its not like everyone has one lying around in their closet lol. *runs over to Canadian tire* Think the local hardware store will have an Ohm-meter?

They definitely should (it will likely be a multimeter), but you'll need to know electronics basics to use it:

[Jimmykaboots]

They definitely should (it will likely be a multimeter), but you'll need to know electronics basics to use it:

Jesus christ it's a lion get in the car.... so the Ohm Meter measures resistance again a lion? Ok wait im confused, i thought that other guy said Ohm Meter is the measuring of friction of metal. So how come you mention a lion?

[aqua_scummm]

Oh simply to prove the point I made in the post before, that I have a lot of junk in my photobucket just wainting to be used.


But yes, hardwear stores sell them, look for an ohm meter or a multmeter, they require batteries, often odd litium ones, so check the packaging.

[Jimmykaboots]

Oh simply to prove the point I made in the post before, that I have a lot of junk in my photobucket just wainting to be used.


But yes, hardwear stores sell them, look for an ohm meter or a multmeter, they require batteries, often odd litium ones, so check the packaging.

O ok thanks, im eager to find out if I have a TI valve, wouldn't that be neat lol. I'd sell it in a heartbeat if I did have it. Probably don;'t though.

[Phantom Power]

Resistance of something (usually a metal wire) depends on both the length of the object (this is the distance between the points you contact with your ohmmeter), the cross sectional area of the object, and the resistivity of the material. Resistivity of materials is temperature dependant.

R = (resistivity * length)/area

So ideally to use the ohmmeter to determine if a valve it Ti, we have to measure a SS one at room temperature (20 degrees celsius) from given points (directly across the valve would work. It's a cylinder so the diameter will the be the same no matter the orientation) and then make sure you do the same measurements on every other valve you test to compare.

I'll be at my shop later this week where I have access to a fairly high quality multimeter. I'll try and get some actual numbers from my Mag valve and work out what a Ti one should read.

Using the numbers that back2integrity posted above, if a SS valve weighs 10.6g that yields a volume of (10.6g / 7.750g/cm^3) = 1.368 cm^3
If that volume were made of Titanium, it would have a mass of (1.368 x 4.507 g/cm^3) = 6.164 g

Of course, those numbers assume that the whole mass 10.6g is composed of SS for the measured valve and all its components, and that every component made in SS was made in Ti for these sought after valves. If we knew exactly which parts were made of Ti then a more accurate value could be obtained.

[Ninjeff]

They definitely should (it will likely be a multimeter), but you'll need to know electronics basics to use it:

:rofl: :rofl:

[Tao]

12.7g w/ on/off and PT tip and Macro fitting (no bolt)

12.0g w/ on/off and tip (no bolt)

11.6g w/ PT tip but no on/off (and no bolt)

10.6g w/ no on/off or PT tip or bolt or nut (11.1g with nut)

Thanks

[koleah]

Holy Cow I nearly choked on my dinner laughing at that thing!


On a slightly more serious note, whats the group's feeling toward how a small out-of-the-way test grind mark will affect the resale value on the non-Ti valves? Maybe done where it can't be seen like underneath where it would be covered up by the rail.

K

Edit: I ask because I sense some hesitance to start grinding to check, but I dont' think a small unnoticeable grind mark will affect anything really. Next time I've got the cutting wheel out, I'll be checking my old valves, resale be darned.

[aqua_scummm]

I was thinking of the back of the valve, like right next to the velocity adjuster, placing it flat against a grinding wheel.


I dunno, as long as it's invisible, can't go hurting the stigma that mags are the best looking markers available!

I'm going to examine other means, including going to the local headshop to price out scales