G-Force to release pneumatic frames for the Mags

[custar]

i think i was the first 1or 2 that ordered, my screen shot says end of November for frame, decmber for lpr,

Mine too.

custar

[Don Carnage]

Garf, what would be the ideal input pressure on an X-valve without ULT?
800 or 1,000 psi?
or does it not really matter since it has the pneumatic trigger?

[Smoothice]

Garf, what would be the ideal input pressure on an X-valve without ULT?
800 or 1,000 psi?
or does it not really matter since it has the pneumatic trigger?

input pressure only matters when trying to bounce.

The pneumag trigger should not bounce no matter what your input pressure is.

If i'm wrong somebody please correct me.

[TnDeathInc]

8/31 is when i ordered.

but your message says send mine first hehe.

[Smoothice]

8/31 is when i ordered.

but your message says send mine first hehe.

Muhahahaha. I'm hoping garf notices that too.

[insixdays777]

input pressure only matters when trying to bounce.

The pneumag trigger should not bounce no matter what your input pressure is.

If i'm wrong somebody please correct me.

That would be great if it could be done...think about it...

A pneumag that has the ability to be SEMI and RAMP.... WOW...there has to be a way,

There is a video on youtube of a pnuemag, ramping/Fullauto at 30cps...wonder how he did that!

[angrysasquatch]

input pressure only matters when trying to bounce.

The pneumag trigger should not bounce no matter what your input pressure is.

If i'm wrong somebody please correct me.

Wouldn't a higher pressure decrease your recharge time, and thus increase the top-end speed?

[Smoothice]

Wouldn't a higher pressure decrease your recharge time, and thus increase the top-end speed?

Yes, Higher pressure decreases your recharge time as well as increases the force pushing the trigger back which makes it easier and faster to bounce your RT valve.

BUT

From my understanding the ability to bounce your trigger and go full auto is due to sweet spotting the trigger. The RT valve actually pushes the sear back which pushes the trigger back.

Also in my understanding with a pneumatic trigger frame the trigger is either pulled or released. I'm not sure if you can sweet spot it because the RT valve would only push back the sear. The sear would then have to push back the piston (which should already be back and reset), which would then have to push air back through the line into the switch (msv-2) which would then have to push back the trigger rod, to then push back the trigger.

All this is based off of current pneumag DIY conversions. I have never seen how the Gforce trigger frame and how it works. So maybe it is possible.

[Smoothice]

That would be great if it could be done...think about it...

A pneumag that has the ability to be SEMI and RAMP.... WOW...there has to be a way,

There is a video on youtube of a pnuemag, ramping/Fullauto at 30cps...wonder how he did that!

When I had first set up my pneuframe with an x valve it did the same thing. I oiled it up and it went away. What I think happened is instead of the ram resetting after a trigger pull like it was supposed to it was stuck open for as long as I had the trigger pulled.

I have no idea why or how it did this. But I was glad it went away.

[warbeak2099]

You'll probably still want at least 800psi so the sear can reset quickly. As long as you have enough pressure for the sear to reset at 15-17cps, you should be fine. I cannot wait for my frame!!!!!!!

[G-Force Tech]

I am using a Crossfire 68/3000 high pressure tank (850psi). It's low cost and does not drop pressure at all. It doesn't matter how fast your Mag can shoot, if the tank has to maintain the 850psi output at all times.

Garf

You'll probably still want at least 800psi so the sear can reset quickly. As long as you have enough pressure for the sear to reset at 15-17cps, you should be fine. I cannot wait for my frame!!!!!!!

[G-Force Tech]

Not possible for a pneu mag to ramp. Ramping need software programming to do it.

The trigger on this frame is so short, you can keep up with any electro. Does it really take 15 balls to take out a player? I see tourney guys spray each other back and forth with 15bps.... where's the skill.

Garf

That would be great if it could be done...think about it...

A pneumag that has the ability to be SEMI and RAMP.... WOW...there has to be a way,

There is a video on youtube of a pnuemag, ramping/Fullauto at 30cps...wonder how he did that!

[jman511115]

Quick side question- I placed an order with you today, but closed the window on the paypal site before I paid because I had some questions that I wanted to figure out before I finished up. It ended up placing the order, but I still haven't paid you guys yet. Any way to go back and access the order and pay up?

[LK-13]

Not possible for a pneu mag to ramp. Ramping need software programming to do it.

The trigger on this frame is so short, you can keep up with any electro. Does it really take 15 balls to take out a player? I see tourney guys spray each other back and forth with 15bps.... where's the skill.

Garf

but should the player volunteer for the surgery we can install the new hypersensitive digital auto FINGER with full auto and raping modes as well as full nasal port cleaning function with single digit hemorrhoid frictional relief system!!

[Anjin3515]

but should the player volunteer for the surgery we can install the new hypersensitive digital auto FINGER with full auto and raping modes as well as full nasal port cleaning function with single digit hemorrhoid frictional relief system!!

However...Smart Parts has already patented this surgery and anyone getting it will have to pay a fee to use their new Auto Finger.