I'm about to throw the level x out the window please help

[Smoothice]

Since PV = nRT where P=pressure, V=volume, n=moles of gas, T=temperature, R is the gas constant, an increase in Temperature leads directly to an increase in Pressure, which means a higher velocity. .

I always hated moles!!!

[lidocaine]

will it maintain a sustained stream of pain or will it just be for 5 or 6 balls? The rt effect that is?

Thank you very much!

[snoopay700]

will it maintain a sustained stream of pain or will it just be for 5 or 6 balls? The rt effect that is?

Thank you very much!

Well this valve has maintained a rate of 34 bps with a special air source, and with a normal tank it can easily keep 20 up, so no, you won't get shootdown, the effect won't disappear.

[Digler45]

I have been fooling arounf with this for some time. I had my level 10 working pretty good for awhile, then it started to leak. Well then I moved down a carrier. I started with the 1.5and gold spring then went down to the 1 with the gold spring. Again it functioned fine. Then the other day I wanted to try to put the middle spring in. Didnt work at all no matter how much I turned the velocity up it didnt fire correctly. Chuffs and broken balls. I put shims in then took them out changed oring and carrier sizes. I tried the oring that was working great in the 1 carrier and put it in the 1.5 and like originally with the gold spring it leaks. Back down to the 1.0 and it doesn't leak, but it doesn't even fire no matter what the velocity is set at. So i gave up and went back to the gold spring with the 1.0 carrier and the oring that is borken in. It doesn't leak, but chuffs on the 1st pull still. Then fires fine. Then if you let it sit for a few seconds it chuffs on the 1st pull again. This was killing me while i was playing today. I never got the "first shot" off. It would just chuff then reset the trigger then it would fire. I pretty much tired of this. What do I do now? I have a retro valve and 1200psi coming into my mag. It chuffs with balls or with out. I'm about to send this back to AGD. Its killing me. I have a warp feed and all balls are being chambered correctly.

edit... when it chuffs and it loaded the ball just rolls out the end of the barrel. Its currently shooting at 280 fps


_barry

Probably way too late, but i had a similar issue with my Tac-One when trying to change springs. I couldnt get it to fire at all once i changed to a longer spring. Adjusting the velocity did not help. I finally got it working by turning the velocity all the way down without it air up. Then slowly increased the velocity until it started to fire. If you got it working, great. If you want a softer feel, use a longer spring. Cheers.

[phatty123]

Probably way too late, but i had a similar issue with my Tac-One when trying to change springs. I couldnt get it to fire at all once i changed to a longer spring. Adjusting the velocity did not help. I finally got it working by turning the velocity all the way down without it air up. Then slowly increased the velocity until it started to fire. If you got it working, great. If you want a softer feel, use a longer spring. Cheers.

Well I found out that my chops pretty much go away with the warp feed and the level 10 with short spring. My paint is never half way in the chamber. It always gets pushed all the way in by the warp and the level x still hits alot softer then the level 7 so its working out for me and I dont have the stomach to mess with it again. Its working and I'm not going to f it up.


-barry

[Digler45]

Well I found out that my chops pretty much go away with the warp feed and the level 10 with short spring. My paint is never half way in the chamber. It always gets pushed all the way in by the warp and the level x still hits alot softer then the level 7 so its working out for me and I dont have the stomach to mess with it again. Its working and I'm not going to f it up.


-barry

Perfect. no need to tinker then. Cheers.