** Official Level 10 Problems Thread **

[Havoc_online]

studley192 Are you sure that's a Level 10 problem? Could be an on/off or trigger rod length problem. Could you give some details of your marker? have you adjusted the rod length? what's your input?

[studley192]

no, i havent messed with anything besides what was neccesary to put in the lvl 10. Before i put it in, it didnt do this, after, it shoots fine, but does this. It might be the on -off, but i didnt do anything to it. Any idea how i can fix it? its not like its a real problem, im just have to have stuff perfect

[ChillinDaMost87]

I've got it going pretty nice but one thing. If Move my barrel around it leaks just the slightest bit down the barrel. Thats the only time. Should I go another size smaller on the carrier or no? Right now I am at the one ring and dot carrier.

[Hemorrhage]

No matter which carrier I use it always leaks out the litte side hole or the back of the valve. Tried em all, tried all the springs, all the shims, I'm getting a little perturbed. I've started from the begining of the directions many many many times. This is my Third DAY working with the x-valve(lvl 10). How long was installation supposed to take? Am I just stupid? HELP!

[knssabo]

my LX will not chrono above 250

i have recently put a LX in my mag. i am using the 2.5 carrier, and the smallest spring yet every time i try to get to adjust above 250 it only vents out the back. what could be wrong
any help would be greately appreciated

[Havoc_online]

studley192 Your input pressure?

ChillinDaMost87 Try the 1.0, see if that works for ya.

Hemorrhage Make sure nothing is missing in the valve and try to oil it up a bit. Since it's new, it may need some working in.

knssabo Make sure the kit is installed properly. Make sure the bolt fits the body. You might try a new reg. piston.

[knssabo]

input presure is 700-800 psi, the mag shoots at a much lower velocity settingwith the normal internals and i have never had a problem with the reg piston. i was told that i might need to get a adjustable tank to turn the press. down. is that really what i need to do. or do i need to increase the preasure to the gun?

[SuperBeast]

I have:

Automag RT (old kind)
level 10 kit

Problem:

At first, after much heartbreak and headache, I got the thing to shoot with a 1.5 carrier, 1 shim and the long unclipped spring. However, the trigger pull was like dragging your leg through molasses!! Also, it seemed as if it could not keep up with my finger. From what I have read, I switched to the short spring that came in the LX kit. Trigger pull is much better. However, before and after changing to the short spring, I would hear a very quiet hiss after each trigger pull. Turned out a very small amount of air was coming out of the back of the gun, where the hole for velocity adjustment is. I suspect the reg piston? Can anybody please explain this? Also, with the short spring, the bolt seems to "hit" a lot harder (finger was used to measure this ). Would switching to the long clipped spring provide a good medium inbetween the short and unclipped long spring?

[hangover247]

problems with the lvl 10 while using a freak back

PLease help, i just bought a RT pro that came with a lvl 10 mod installed. When i use the stock barrel i dont have any problems but when i use the freak barrel i have the gun wont fire. The trigger just wobbles back and forth. I have to unscrew the tank and then screw it back in to recock the gun, then it will only fire once or twice then the problem happens again. please help, thank you. Hangover247

[t-square]

questions, questions, questions!

this might not be the right place but i want to thank mr kaye and the folks that work this thread. i sponsor 2 five man teams who all shoot mags. that's 12 guns (including the alternates) and to say the least it has been an interesting month installing 12 level 10's.

some advice to anyone that might be thinking about posting a problem/question. i was able to find every answer to my questions by scrolling through this thread. it's all here folks.

thanks again for a great thread.

mick
t-square paintball
jacksonville arkansas

[AutomagRT1483]

Here's my problem:
I was out playing today and I was choping all day. When I talked to one of the techs from the field he told me that I should go to the cut spring on my LvL 10. When I put in the cut spring, my RTP wouldn't fire. So I tried the other long spring and it did the same thing. What do I do to get it to fire?

[Havoc_online]

knssabo - get a new reg. piston.

SuperBeast - use the cut spring(cut side on bolt) and when swtich springs, you must rechrono.


hangover247 - take off the barrel and remove the valve. Check to see how the bolt fits inside the barrel.

t-square - thanks for commenting! and yes, most if not all the info is here, just read. As for you and your teams - you MUST get them here on AO and post some pics for the rest of AO to see. what do they play? how are they doing?

AutomagRT1483 - did you try turning up your velocity when going to the longer springs? what's your input pressure?

[AutomagRT1483]

It worked after I turned up the velocity, thanks.

[Hemorrhage]

No carriers work, all vent out either back hole or side hole of the valve (x-valve)at all veloticty settings. My velocity adjuster thing is on the verge of being stripped it seems like and I've gone through 2SCUBA tanks of air to try to fix this bugger. Any ideas??? HELP!

[GhillieGuy]

I have a hyperframe, the on/off pin is just pressureized and wont fire. When i installed the level 10 on my other mag with a benchi, it did the same thing: when i pulled the trigger the sear pin was pressureized but it did not fire. I have a 1.5 carrier, 2 shimes, and the medium spring.