** Official Level 10 Problems Thread **

[Plazmic]

That's awesome! I didn't even think of the trigger rod length. Good job, my man!

[Cthulhu]

Ya, from what I can see, because the old bolt is worn, the sear was releasing it. Now with the new level 10 bolt, it must have been just barely catching it, and sometimes allowing the bolt to fire. By lengthening the rod, its forcing the sear down lower, hence allowing the bolt to fire.

All I care is this darned thing fires!

[Auto_Rook]

I just ordered my X valve and ULE Trigger kit.. right now i have to put the original parts back into the classic valve to ship it out... i dont know what to do beacuse i had level 10 in it.. what do i put back into the classic valve??

[slade]

dont you just put the stock parts/bolt back into it?

[Auto_Rook]

thats the problem.. idk what the stock parts were except for the bolt and spring.. see i didnt do the level 10 install so idk what he took out..

[slade]

what parts did he give you back? i got my gun w/ the xvalve, so i dont know too much about what came stock in the power tube, but looking at the diagram at http://www.airgun.com/downloads/valveexplodedview.pdf it looks like you'll need a power tube spacer and a different power tube tip. so you'll have to take the carrier that is in your power tube and the power tube tip off, and replace them with the stock parts. you probably could send your valve with the level 10 to agd, but i doubt that youd want to do that.

[Auto_Rook]

ok i put the stock thingy back intot he valve where the level 10 would go and i put the stock tip thingy on and the bolt and spring.. i cant test it out though. i have no air.. o well

[Auto_Rook]

Ok now that im going to get my X valve soon.. i have to do my level 10 on my own.. Sooo what are the steps i follow.

[slade]

the level 10 comes with a cd that will tell you everything you need to know about installing and tuning it. just read through it and you'll be fine. the basic idea is that you just install the middle size carrier and then change the size of it up or down based on if it leaks or if it provides too much friction.

[ejm]

new x valve

i just bought an x valve for my minimag my problem is i cant seem to get it to quit leaking down the barrel a bit. if i barely touch the trigger it stops. i have gotten it to stop for a bit then it starts im down to the smallest carrier with 1 shim and it still leaks with 2,3,4, or 0 shims still leaks a bit. any sugestions.


ejm

[Plazmic]

Check your on/off and make sure it's in properly.

Also, are you using the same o-ring in each carrier or are you using a different one in each?

[ejm]

on/off looks fine same oring in each. the on/off is to short for my hyperframe it wont even connect with sear. but in standard frame it shots but leaks a very little bit

[ejm]

got it working with smallest carrier and 1 shim. now it wont leak down the barrell also is using the red spring.

[PRPB]

OK I just istalled a ULE and lvl 10 on my teammates mag. I have the lvl 10 set up and working good, but every once in a while the trigger does not reset. I degas it then add some oil and it will fire for a few hundred then stop again.

Also it does not want to stop venting out from the back. Its running around 280 and if I lower it anymore it will not fire.

[fbpb36]

I am using a lvl 10 with 3 shims and the small spring. I couldn't get velocity high enough with the larger spring. It was working perfect utill about 500 rounds went through it. Now it leaks, it stops though if i push the bolt back with my finger. What should I do to get it working better.