** Official Level 10 Problems Thread **

[Gijim]

Got a suggestion

I found out that my level 10 was shooting over 300 because I didn't oil up all the new orings enough. I makes a big difference so make sure you use quite a bit of oil. I went from 310ish area to 250 just oiling it properly.

[Outlaw5]

LVL 10 MOD

To TK, JON and the rest of the crew at AGD.... You are strictly the HEAT!!!!! The LVL 10 turned my good, balanced marker with marginal chop problems, to a fire breathing dragon!!!!! I sent my Mini in during Jan for a full overhaul of the original valve, I called in to insure they had received my marker and that the RA number was good. I believe it was Jon who talked to me about just upgrading the valve assembly to an x-valve with LVL 10 installed. I'm a money hording fool so at first I wasn't sure, but hey I needed a christmas present to myself so I said to go ahead. I received my marker in the beginning of Feb, about a three week turn around because of x-valve production. I went to my local store,FREEDOM PAINTBALL-IN FAYETTEVILLE NC, I have no shame for advertising for buds.. and I fired 500 rnds through the marker in about 3 minutes. I was impressed!!!! I had to oil the new valve extensively to get it broken in but this took a little time only. Now I have been chomping at the bit to go and play for two months. I played today (29 MAR) at Paintball Sportsland in Frederick Maryland.. excellent staff and fields-highly recommended! My Mini went from "Nailgun" to hey let me check that beast out! Players who are diehard cocker and electro players wanted to play with this thing. All enjoyed pulling the trigger and were very impressed with the LVL 10. I am thoroughly estatic with the products. Again to make a long story short.....TK and the crew...YOU GUYS AND THE LEVEL 10 ROCK!!!!!!
Another statified customer.

[GhillieGuy]

Please dont say that... now your just rubbing that in couse i have no mony to gets me one...

[Fnoskar]

[GhillieGuy]

Fnoskar try going down carriers, if that dont work then take shimes out 1 by 1...

[maglover52]

i tried that and it started just going crazy and shooting then stoped and started leaking air out or the barrel??? i dont get it?

[kenny45749]

I have a few basic suggestions that I hope may help. If they dont pertain to your situation I am sorry, but I hope they do. From you saying that the gun doesnt fire at all, I am guessing that this leaking starts upon gassing up the gun. Is that true? If it is, there a chance the gun isnt sealing properly during initial gas up. Do you hold down the trigger in manual or hybrid mode when airing up the gun? This seems to help in keeping barrel leaks off the get go from happening for me.
Also it seems like I heard somewhere that the on off can yeild barrel leaks if it fails to seal, but i cant find that in my information I have compiled. Well hope you figure it out.

[crankydan]

EMAG LX QUESTION

I installed the LX in my EMAG, went through the oring break in and installed smaller carrier with barrel leaks. This is my question, since I installed the largest spring(I really like the soft bolt with brittle paint), everytime I gas up, it coughs out the reg hole like 3 or 4 times. If I de-gas and re-gas it stops and marker works great other than me short stroking in mechanical mode. Is this ok or will it cause damage in the long run. I can fix this by installing the mid spring, but the bolt pinch is increased. I just dont want to cause any on/off or reg piston damage. Thanks for any advice.

[maglover52]

mine when i turn the velocity all the way up just leaks down the barrel? and the sear doesnt push forward enough so that i can shoot it to break it in please please help me.

[Fnoskar]

[Maclete]

Tuning my Lvl 10 -- Help

I have a 68 classic and have it running on the middle spring with about 1/4 turn cut off (per AGD tech support). It has been running fine, but is leaking down the barrel. I pulled it apart and re-lubbed it and it will run fine for about 400 shots then starts leaking. Will removing shims help. I want to try other thing besides going to the next carrier. Also it almost runs on the largests spring. I get a few shots off before it vents and stops firing. I have a tournament screw for velocity adjustment, should I remove that as well for better tuning?

Thanks for your input.

[maglover52]

i have the velocity all the way up with the 1 dot spacer and the medium spring and it was leaking down the back then i pulled the trigger and it shot and stoped leaking for a second then started again and was leaking still i continued this for like 20 seconds then it started just leaking down the barrel???

[archdemon]

I just put in my level ten in my minimag with the second largest spring and the carrier with no grooves. For some reason when i pull the trigger nothing happens. please help

[GhillieGuy]

Archdemon- When you pull the trigger is the on/off pin just pressureized? Turn up your velocity until it clicks.. If this doesnt work then try using the smallest spring in the pack.. What is your input pressure? I was having the same exact probs with my mini.

[archdemon]

i dont know my input and neither of those thigns helped ne other suggestions?>