** Official Level 10 Problems Thread **

[MagOwnerzRule]

What to do

ok i think i have everything right but... when i go to put it on it will not fit the bolt want go on what do i do?

[rmhawk]

could you clarify?

[MagOwnerzRule]

like the bolt will not slide on to the rod... dunno what its called..

[rmhawk]

aahh...that, my friend, goes beyond me. sorry. i know a little bit about helping with level 10 problems, but when it comes to that, i don't know. i have heard about that problem before, but its pages back.

[Benfica4ever]

Ok. see. my lvl 10 shoots fine, but there is still a leak, its comming from the bolt. i have taken over 50 shots but it still leaks a bit. whats the problem?

[rmhawk]

whats the carrier/shim setup? If i had to guess, i'd say drop down one carrier, but remember to keep the same o-ring you're using now!

[scorpion1666]

Not sure what's wrong

Well, after installing the lvl 10 per the instructions, The bolt does not seem to be ..lets say gentle to anything...hehe. It still has the punching power of a regular bolt. I went down to the 1.5 carrier and 2 shims (as most people are suggesting) even though per the instructions, the 2.5 carrier was fitting it correctly. I'm at a loss. Even when just doing the 1st test with out the shims and orginal spring it was not giving way 1 bit with any of the carriers and still acting like a normal bolt. This is with the X-Valve, but I do not believe it is the valve...but I could be wrong. I went ahead and put it all the way together to see if I was just not realizing that that was what it was suppose to do, but still no luck.

Any suggestions and or help would be greatly appreciative.


-Schuck

[SomebodySomeoneRTPcf]

my lvl ten is leaking/ but can't be heard. It takes about a day to lose 1k of pressure and i tried every insert to sotp it. could i take it to your factory so i can get it looked at? also can the factory check that my rt is o,. just to make sure none of my o-rings r leaking? I live in chicago on the north side so it should be fairly eaisy to get to you.

[The Deacon]

I fixed it, next size up carrier and small spring, and it's good.

Ok, here's the deal:

My lx is funking out on me. I shoot a Classic RT w/ LX run it with a Crossfire tank preset for 850 psi output.

I gas up and get a good 10-30 shots. I let it stick, and the bolt sticks. The trigger bounces back, but the gun doesn't cycle. I puch the bolt, it shoots some. I tried all possible combos of shims, and the best I got it down to was with 2, where I can shoot 10-30, then if it sits for more than 3 seconds, the bolt sticks, the next shot vents, and it shoots a few times, randomly venting every once and a while. I've turned the velocity up, and it does nothing. I have the shortest spring that came with the LX, because anything else won't let it fire. Any ideas?

[Justin Richardson]

problems

i just put my new mag together a couple of days ago, i'm now trying to fine tune the lx on the x valve that i have, but its not going so well. i'v got the #2 carrier in (2.5 leaks) and at the moment trying out the mediem spring. i can't get the velocity high enough for it to run reliably without the reg nut leaking. with the smallest spring it does fine, but the bolt doesn't return when i place my finger in front of it, and if i put anouther shim in (one is in already) it starts leaking, and with the one shim in and nothing leaking, when i fire air comes out of the reg nut this also happens when i just hold the trigger in but its just for a split second. any help would be greatly appreciated!!!

[[email protected]]

foamy

hey I have been having trouble getting my foamy to stay in my lvl 10 i bought one yesterday and glued it with super glue and let it dry the night when i woak up i shot the gun. i looked down the barrel and the foamy was gone. is there another alternative to foamys or should i try a better glue please suggest an alternative and a type of glue. THANKYOU FOR UR TIME

[Spydermann]

planning on buying an x valve

well im planning on buying an x valve...but will it come with a troubleshooting booklet or something like that for the lvl ten bolt that comes with it?..

[rmhawk]

your looking at an excellent troubleshooting booklet. this entire thread helps with just about every problem.

[Spydermann]

Figured

LoL...I figured that someone whould say that..but ur right this is..

[ugabiged88]

Ok, when your bolt stops on a ball is it supposed to automatically reset or do you have to pull the trigger again before it stops leaking?

Get back to me soon!