ego mag build

[RT Lover]

ok building a ego mag and wanted to used a way cheaper noid than most, if its good enough for a viking or timmy good enough for a ego mag lol

here is what i have

http://macvalves.com/Portals/97890/docs/43catalog.pdf

its to big to fit in the grip with the battery but i can maybe fit it in the rail or i will gut a as thru lol i cool with that

things i need to know is what ports to use on the noid... whats in out and vent if any? i go crossed eyed after long reading so hoping if someone can help me some lol

do i just wire the two wires off the noid straight to the 2 on the ego board on my noids both wires r gray? does it matter what wire go where..... there both gray on the noid.

can i just use a 9volt battery and not have to use anything else to not fry the noid or under or over power it?

ty guys

[BTAutoMag]

there's one on here too but PBN's search works better

http://www.pbnation.com/showthread.php?t=3518618&page=2

[renie]

they work fine straight off a 9v Lucky used the 3 port version on there ion mods there a very reliable noid and have a high cycle rate, I have loads of the 5 port ones just never used them it doesn't matter which way you wire the noid leads.

if I can help you anyway feel free to ask

[RT Lover]

thanks bt alot of the threads here on ao the links and pics dont work....

renie on my noid what ports do i use? I assume in, out/vent?

thanks for the info!!

[renie]

it should be on the sticker on the side of the noid ill get you a pic of the one I got in 2 mins, I have the 3 port version off an old lucky ion and that uses usually open ports going from port 3 input to port 2 output with continues flow and when activated closes port 2 which on an ion dumps the forward pressure.

you want the usually closed setup so once activated the air flows to your activator, on this noid it would be port 1 input port 2 output.

if your not sure you can always blow through it and test which ports work

[renie]

[renie]

on the 5 port version port 3 input is normally closed when activated flows to port but it has a vent on the spool base so what your best setup would be is input port 1 blank port 2 making your output port 4 which in turn makes port 5 your vent

[RT Lover]

will have to start blanking ports

u mean plug the ports im not using or can i leave them open and port 3 in and port 2 out is what i want? the ports r stamped i didnt see that at first lol. should i wrap the noid with electric tape or something to insulate it? I picked up this noid for 10$ and figured it was no big loss if i messed it up lol.

what are some noids that will fit in the grip frame with the battery?

ty Renie

[renie]

you only need to blank port 2 if you have the 5 port version

the small noids that fit in the frames are the SMC S070c-SDG-32 there only rated to about 60-70 psi

or you can use the festo noid setup like I did on a couple of my builds from the WGP trilogy they have a 200psi rating

[RT Lover]

you only need to blank port 2 if you have the 5 port version

the small noids that fit in the frames are the SMC S070c-SDG-32 there only rated to about 60-70 psi

or you can use the festo noid setup like I did on a couple of my builds from the WGP trilogy they have a 200psi rating

do you have a build link? my big tank is a ninja shp at 11k out put should i not use this.... i dont want to hurt anything? what size barbs and plug should i get? can i just plug the other ports just to be safe?

do you have TW to cocker adapter by chance?

ty sir

[renie]

Think there 1/8th barbs with m3 thread you will need a decent lpr microrock are popular
ill get u some links once I get home from work
ive used the SP miniflow lpr aswell with good results

[renie]

heres an ego mag with the WGP festo noid setup

http://www.pbnation.com/showthread.php?t=3696293&highlight=egomag

creemag mag build using smc noid

http://www.pbnation.com/showthread.php?t=3848265&highlight=renie

[RT Lover]

where can i get some noids and fittings etc, air solider isnt working right... but u r across the pond.... how long is shipping on that

ty!

[renie]

Your struggle to get the wgp setup the smc can be got from most smc retailers I use s company called RS components.
Ill have a look see if I can find anyone near you

[renie]

smc noid here

http://www.smcpneumatics.com/S070C-SDG-32.html

barb fittings

http://www.pneumadyne.com/threads-straight-connector-fittings-p-2411-l-en.html