Wedge design.

[OPBN]

Cant you elbow the hole? drill part way down from the top and then come back through from the bottom? I don't think the hole has to be that big.

[river031403]

Wedge

At this point were just trying to get him to make one like NDZ's wedge.

[luke]

At this point were just trying to get him to make one like NDZ's wedge.

No worries, I'm just going to keep it simple at this point and get it done (after the grip frame) I have materials already for a simple wedge.

[river031403]

You

No worries, I'm just going to keep it simple at this point and get it done (after the grip frame) I have materials already for a simple wedge.

Thanks Luke!

[need4reebs]

you could possibly use a LPR extension that could go thru the Wedge? that would eliminate the extra O-ring? if you have access to a square aluminum block, drill holes to mount to the frame and then cut the square aluminum block into two 45 degree triangles and then you will have to wedges to experiment with? countersink the mounting holes to the frame, drill and tap the holes to mount a ASA and then drill a hole up the middle of the wedge big enough for the LPR extension to go thru? hopefully i said that right? if not my bad? if i had the machines to do it i would try it out, but it shouldnt be too hard to do with the proper tools?

[need4reebs]

you could possibly use a LPR extension that could go thru the Wedge? that would eliminate the extra O-ring? if you have access to a square aluminum block, drill holes to mount to the frame and then cut the square aluminum block into two 45 degree triangles and then you will have to wedges to experiment with? countersink the mounting holes to the frame, drill and tap the holes to mount a ASA and then drill a hole up the middle of the wedge big enough for the LPR extension to go thru? hopefully i said that right? if not my bad? if i had the machines to do it i would try it out, but it shouldnt be too hard to do with the proper tools?

and Crickets to another good idea? oh well???

[river031403]

Lpr extension

You got pics of Lpr extension

[Arstron]

I would love to see something bigger then a wedge, something like the old endo cradle that not only angled the tank, but pushed it back away from the trigger frame as well.

[need4reebs]

You got pics of Lpr extension

there is a pic in the Pneumag kit section

[luke]

Guys, I'm a one man band, I can only do one project at a time.

I would love to see something bigger then a wedge, something like the old endo cradle that not only angled the tank, but pushed it back away from the trigger frame as well.

That is what I'm looking into instead of the off-set, just kicking it back a tad will clean up the grip-wrist-tank problem.

Here is what I was working on>

[Ando]

wrong angle.

[river031403]

Incorrecto

No bueno sorry I know it takes time effort swet etc. just s simple new Luke designz angled drop kick would do just fine. I have a New Designz Drop Kick waiting for me in the mailbox as soon as I get home I can take photos and measurements if you'd like look

[need4reebs]

those look like the ol Kapp drops, just these have a dove tail...i cant remember if the Kapp drops have the dove tail or not tho?

nope the kapp drop doesnt have a dovetail...here is a pic:

http://www.ebay.com/itm/Kapp-Drop-Fo...item22f51d92c7

[Arstron]

hmmm I like it Luke. Just estimating comparing that to my endo, it should put the tank around the same area as the Endo Jr would.

[luke]

I will have to do a mockup to figure out a good angle, just moving the tank back changes how the tank rests on the shoulder. But I think this will fix the grip/tank/wrist issue.