ULE Trigger Kits in the Store!!

[Jerhew]

really?
i expected you to say a classic...
have you spent some time tuning it at all?
from what i gather, using the right amount of shims helps a lot
how much did you mess with it?

[chd03675]

4 shims with the .5 carrier or the 2nd to smallest carrier wiht the dot

[Jerhew]

wait
carrier?
do you mean the level 10?
you should have shims to adjust your ule trigger also

[chd03675]

2 shims in ule trigger

[Jerhew]

well i wish i could be of assistance
my ulet won't be here til friday
i hope im not disappointed when i get it

[Dayspring]

The ULT will do nothing for Emag battery consumption. The software doesn't control it either. The solenoid draws a specific amount of power, every shot w/o fail. In order to get better battery life (which is 20,000 shots) you'd need a smaller 'noid.

It's not like an engine that can save gas b/c the engine isn't working as hard/under load.

Originally posted by speedyejl
Can we look foward to a software update for e/xmags which will take advantadge of the ULEs lighter pull in better battery consumption or higher ROF?

[Newbie]

Is this new trigger light enough so that you can "walk" the trigger??

[silentdeath55]

I should get mine today. I just checked the tracking thing on UPS and it is "out for delvery".

I dont think this trigger is light enought to be walked mainly because the trigger pull is not any shorter than a stock mag.

[Evil Bob]

It's light enough to walk if you're a bass/tuba player or someone with very strong fingers. Other then that, you will have a hard time walking it.

-Evil Bob

[painball]

i can walk my trigger without the ULT. Im sure i will be able to with it

[BlackVCG]

I have a thread dedicated to ULT tech questions and other info about the setup in the Tech Forum. I also have a couple of videos in that thread of me shooting the ULT on my XRTP.

http://www.automags.org/forums/showthread.php?s=&threadid=96538

For the person that was having short stroke problems, you need to install more shims in the ULT. Not sure how many shims AGD is including in the kits, but you can use one Level 10 shim to replace two ULT shims. So if you only got two shims with the ULT, put one LX shim in and then add one ULT shim and try that and then you can add one more ULT shim if it still isn't the way you like it.

Remember, don't think that with this trigger you can walk it like it's an E-Blade Cocker. It's going to take some practice to get it going fast. I don't think it's walkable, but I don't walk any triggers. To me, walking is just for show.

[Evil Bob]

Thanks Black, good info.

-Evil Bob

[QUINCYMASSGUY]

trigger

AGD, great work I am impressed. Got my ULE, went in as is no problems, shot well but I threw an extra shim in there and it brought the recharge point nice and close. I like that it is already assembled, curious to know that if the on/off pin is sent connected to the support how we take the pin out if we need to (gets bent, etc) but otherwise top quality work.

EDIT: Good joke with the answer at the bottom: Why couldn't the Mag walk too fast?

Little notes for others curious about it: walking is definitely a real tough thing to do but it's more about the length of the pull than the weight that seemed to make it tricky for me. Whatever, I'm ripping on the thing with one finger. I can definitely see where it will suck in classic valves, the kickback is minimal in Xvalves so it'd be real easy to shortstroke a classic. Comes assembled, compared to the Lvl 10 it is a breeze to adjust. Strange thing is by putting this on/off in I think it may have made it visible that I have one too many shims in my Lvl 10. Lightly pulling causes a little down-barrel leak and I know it's not the carrier. Just pointing that out in case any of you get the issue too, just pull a shim out.

And I do think a trigger stop would be beneficial in the back end of the stroke, but I am wary about a front one. If Tom Kaye says bad idea (or in his words, hummm, more bolt being bought or whatever it was he posted a couple weeks back) I'd believe him. We'll see what happens with the back stop though.

So great job AGD, I definitely recommend anyone who can get one, does get one. Joke answer: Because it had shim-splints. Oh come on, that was funny! Runners will get it!

[painball]

im wondering. in my x-valve now i can barely pull the trigger enough so that the pin goes in all the way by itself and fires. Now will I be able to have it do that with my ULT? Is this even normal for my marker to do that?

[silentdeath55]

Got mine yesterday and installed it in about 5 minutes(not including resetting all the shims). I am very impressed with this trigger, even in a classic AIR valve. Great work!