Agg Mag (mQ-Valve)

[Athius]

Finally a f'n new design of the automag goddammit!!!!!!!! Too bad AGD isn't making it. Pretty ironic huh?

Well this is not a mag but this is the evolution of the mag.

With that mag i think people will think "hAir trigger who???"

[Breck]

What type of barrel is that?

[mquinn96]

We had to machine 6 parts to make the new valve. No rail modification was needed.
The gun does NOT work like a Freestyle. That gun uses air to keep the bolt back. The bolt pin sits against a seal at the back of the power tube. They then use a 3-way valve to dump air out from in front of the bolt to allow it to fire.
The Q-mag works much more like a traditional mag with a spring pushing the bolt back.
The on/off and sear are replaced by the new valve mechanism.
We did the machining in our lab located off-site from the field.

[Duck Hunt]

I don't know much about pnuematics and such, but correct me if I'm wrong...

The Mag valve already can cycle as fast as any gun out there. And its already been proven that it can take ALOT more pressure than any other valve around. But too me the idea of putting an Eblade on a mag seems pointless. The way I see it all you'd have to do it connect the solenoid to the sear and it would do that same thing, just the the EMag and XMag and Hyperframe etc. Why do it any other way?

Sean

[Skoad]

sounds awesome.

Would really love to see a video of it. I'll be waiting

[mquinn96]

I don't know much about pnuematics and such, but correct me if I'm wrong...

The Mag valve already can cycle as fast as any gun out there. And its already been proven that it can take ALOT more pressure than any other valve around. But too me the idea of putting an Eblade on a mag seems pointless. The way I see it all you'd have to do it connect the solenoid to the sear and it would do that same thing, just the the EMag and XMag and Hyperframe etc. Why do it any other way?

Sean

We only used the e-blade frame because it was available. We did not use the sear from it since this valve does not use a sear.

[Lessthanusual]

New board in Emag frame?

Yes, I know the big battery won't be there (and I would be very happy about this). More to the point, I was wondering if you could fit the board you're using into the mag grip along with the battery, (and any other parts) Another idea could be using the empty space to hold an ACE for instance. Or, completely removing the battery housing and milling a new hollow grip.

The question is why? You don't need the big battery any more. And since we don't need the sear assembly, you don't need the plunger assembly. A hyperframe would do well enough.

I for one would be interested in seeing one that could fit in the emag trigger frame and RT type rail.

I'm sure it co9uld be configured to do so. It's just a matter of changing wiring connections.

But it's more intended for people going from a mech Mag to an electronic option.

Less.

[PBX Ronin 23]

Ok, I don't know if this has been answered yet but I still don't quite understand the mQ-valve. If there's no sear how does it work? How could you make a blowforward electropneumatic? My mind is hitting a concrete wall lol, if it seems obvious to other people I'm very sorry. I just want to know how this thing is different in operation than a mag. I mean, it seems to me they just made their own aftermarket mag valve since it still uses a mag bolt and powertube and everything. I know it's something completely different, but how? How does it work? A schematic would be so awesome.

The mQ-Valve is a new technology that PBX will be releasing at World Cup. The initial run will be platformed on the venerable Autococker. In the Cocker, it rplaces the Nelson-style poppet vavle, hammer, sear, lug, IVG and springs. It is electronically activated so when you're trying to 'sweet spot' a cocker, you can "super sweet stop" it in 0.25ms increments. The Lock TIme is 3-4ms compared to other electros that are at 10-15ms. It's cyclic speed potential is considerably higher that ANYTHING else out there. We were able to get 36bps out of the Cocker and the only limiting factor being the loader. WE KNOW WE CAN EASILY GO HIGHER THAN ANYTHING ELSE OUT THERE.

We have platformed this thing on other types of guns. The "agg Mag" being the linear/single tube version that we know we can put in practically anything including spool valved guns. We've also proven that it can be put into a stacked bolt blow-back body and instantly turns it into a Muppet Moving Machine (MMM).

are we looking a LP cocker-mag now???

We can, if we wanted to. We can also configure the design to withstand higher pressures as to not require an in-line reg.

There's lots of options available to us when it comes to designing with this valve.

I bet you it works just the same as a ICD Freestyle, except it looks a whole lot better than a Freestyle! If someone can pull up a Freestyle working animation, I bet it works nearly exactly the same, just the main air passages are routed different.

Absolutely NOT.

What type of barrel is that?

One of the original old-school minicocker stock barrels.

I don't know much about pnuematics and such, but correct me if I'm wrong...

The Mag valve already can cycle as fast as any gun out there. And its already been proven that it can take ALOT more pressure than any other valve around. But too me the idea of putting an Eblade on a mag seems pointless. The way I see it all you'd have to do it connect the solenoid to the sear and it would do that same thing, just the the EMag and XMag and Hyperframe etc. Why do it any other way?

If it's just the valve, I believe we can go 120cps. In practical execution that goes significantly lower because of all the other components that is needed to fire a ball.

It takes less energy to fire the gun with the mQ-Valve. It is significantly lighter. It is more forgiving in terms of manufacturing tolerances. There are no mechnical interface that will wear down after awhile. These are some of the advantages.

Like in anything else, one man's "pointless" endeavor is another man's breakthrough accomplishment. It all depends on your perspective.

It works and as an intellectual property, it's protected. It is our hope that this new valve represents a breakthrough in gun design technology that will positively impact paintball as a sport and as an industry.

[WenULiVeUdiE]

We have platformed this thing on other types of guns. The "agg Mag" being the linear/single tube version that we know we can put in practically anything including spool valved guns. We've also proven that it can be put into a stacked bolt blow-back body and instantly turns it into a Muppet Moving Machine (MMM).

It is our hope that this new valve represents a breakthrough in gun design technology that will positively impact paintball as a sport and as an industry.

How do you do it!? When I heard about you opening a field, I thought " Ok great, another field, can't wait" but never did I expect this much out of you guys.

So the mQ can be fitted to almost any electro-pnuematic then? That's one versital valve...


Andrew

[AGDlover]

so whats the out put preasure are we looking at when a finished product is made?

[PBX Ronin 23]

so whats the out put preasure are we looking at when a finished product is made?

Each gun that the valve is platformed on will vary. We're looking at keeping the pressure for Mag users at the level that they're accustomed to.

[Adrenaline_Junkie]

Each gun that the valve is platformed on will vary. We're looking at keeping the pressure for Mag users at the level that they're accustomed to.

Keeping it high pressure like normal mags is cool but please try and get it to have better efficiency. Even if that means making it LP please try it.

[PBX Ronin 23]

Efficiency is definitely high on my list of attributes that this potential product must have. We can definitely lighten the bolt and the springs and keep the dwell time extremely short.

We'll try to share as much info with you guys as possible and hopefully we can get good constructive feedbacks from you. Everything PBX Ballistix Lab does is done for the players by players.

[the electrician]

very interesting indeed.

good to see another idea/application.
I always like to see another option to whats out there already.

now, one discrepancy I read was that "a spring keeps the bolt back, like in a regular mag"

in reality, the sping only returns the bolt. the sear actually holds the bolt in place. now I'm not really trying to bust your chops on this, I'm just trying to understand. seems like the chamber of air is not pushing on the bolt? perhaps the Mq valve does not apply air to the bolt until it is ready to fire? then , since the Mq valve is controlled by a solenoid(or solenoid valve) the dwell time is controlled?

basically I'm just trying to draw some info out of you

you know the deal, most people just want to shoot it. I want to take it apart first

[PBX Ronin 23]

The spring holds the bolt back but it doesn't need to help seal anything. The sealing is done by the mQ-Valve. There is no longer a need for the sear in this application.

We had to basically use a Level 7 bolt and stock springs for expediency. I wish I knew that we had a Super Bolt somewhere in the shop.

Basically, when the gun is fired, air is released by the mQ-V to propel the bolt forward. Then it releases the air and then it closes. Being that it doesn't have to fight against any residual air that's still in the power tube assembly, the bolt meets with no resistance when returning into the open position. On its return back to its original position, air is vented as to prevent any kind of 'dead-heading'. Ergo, the spring is all it uses to hold the bolt back. The trick then is finding the right spring that would be as light as possible and still return the bolt fast enough.

The cool thing about this is the ability to control and fine tune the gun in ways that's never been done before..........and that's the really amazing part about it.