Round Two

[ta2maki]

Here, this may help, it's Zap's web site. Go to Ghetto Gun Shop.

http://zapsmadhouse.freeforums.org/i...a2fbffb31cabf2

Hi, I dropped mine into a chimera. I had to dremmel the front corners of the cheater to get it to sit a little forward. I then fit it to the point that the trigger doesn't activate the cheater when the safety was on. This worked perfect for me. I think I am about an 1/16" from the sear. I think you can also move it a little further away. I remember someone saying that about an 1/8" is idea. Trick is to move it a little away, test it. If it seems to be shortstroking quite a bit, move it a little further from the sear, and repeat until you are comfortable. Hope that helps. You can see some pics of mine in the paintball talk section. The thread is titled "Pneumagf complete, for now..." Good Luck

Thanks, that helped a lot. I tried 1/8", but that's too much gap. It causes the piston oring to pop out. 1/16" seems to be best. For mine, I had to grind the trigger pin down as I'm using an AGD trigger in the chimera.

[Shirow]

For anyone planning to put this into an M90, it fits easily but the bad thing is that it is almost impossible to see the sear distance in the frame because the Cheater sits pretty high up in the frame so it's pretty hard to adjust.

[skyless]

Zap "themad" Santa

Hey Zap, do you think the last installs will make it befor Xmas?
-#31

[ZapTheMad]

None of the installs are going to make it before X-mas. Too much stuff to do and not enough time to do it! Latest project was fixing my Aunt's fridge. Now on to Gammy's car. Need to do some more bodywork and do something about the duct tape and bailing wire that's falling off.

I've been keeping at it on the installs, tho a bit slow. Putting in at least an hour or so every evening. I would work later but it's been too dang cold!

Almost done with the first one. Going to try and finish it up tomorrow.

Hey Zap, do you think the last installs will make it befor Xmas?
-#31

[Shirow]

If anyone is still looking for a Cheater, I'm selling mine here -> http://automags.org/forums/showthread.php?t=247759

Nothing wrong with it, you can read the story in the thread

/hijack over

[Storminnorman]

got mine installed with a classic valve and tickler. This thing is amazing and fast, thanks again zap.
Also anyone have a pic of a intelli frame with a sear stop. I haven't done one before but all I need is a pic of one done to do it. pm me if anyone could.

[longi]

Mine arrived on the 24th . Just one question, the rod on mine just pulls out of the brass valve, is this supposed to happen? Or is it suppoed to be attached inside the brass valve?

[smeek]

Mine arrived on the 24th . Just one question, the rod on mine just pulls out of the brass valve, is this supposed to happen? Or is it suppoed to be attached inside the brass valve?

The activation rod isn't attached, mine fell out when I took it out of the package. The tapered end goes in the valve when you install it.

[longi]

Phew!! I thought mine had broken before i'd has chance to install it.

[kszyszkowski]

I still wait for mine #8 to arrive. Polish Post Office still must have holidays I guess....Let's wait another week...

[Tombola]

still:

Germany, 0 Cheaters :-(

[kszyszkowski]

Postman dropped some package today. I will be able to check it in the evening

Lets hope this is it

Just checked - YES YESY YES - this is Cheater ! Will mount ittomorrow or today if I will manage.Will post photoz on ZAP's site.

Some update here:

http://zapsmadhouse.freeforums.org/cheater-install-v2-t15.html

[gunman_2000]

*sigh*
still waiting on the postal service up here.

Zap, I'll probably have to talk to you about sending my frame to make it fit too anyway.

Happy New Year

[Tombola]

they arrived today!!
thanks!

[DevilMan]

Hey Zap, can you tell me if you got #35 shipped out to me or not?? Still waiting for it to show up...

Thanx!!!

DM