** Official Level 10 Problems Thread **

[Havoc_online]

I'm going to assume you didnt chrono when you shot the 50 times. It sounds like you need to get your velocity up some more(till it fires reliably, to do that you may need a new reg. piston.(check the o'ring on the reg. piston just incase).

It's not a shim problem.

[Tankdriver]

.

Nope, don't have a chrono.

This firing for about ~50 shots, then stops firing completely is frustrating. I can't be expected to bring a hex wrench onto the game and tinker with my velocity mid game.

Ok, going to give AGD a call for a new piston. I'm 99% positive it's not the carrier size/spring/shim issue. If that doesn't work, an RA might be in order.

[Greg711]

CO2?

Might be a dumb question, but the LVL 10 does work ok with CO2, right?

[dugger]

co2

works great for me.
-dugger

[MINIMAG4LIFE]

my lv 10 foamy keeps blowing loose

My lv 10 foamy keeps blowing off, Ive tried super glue and it still blows off, I've noticed that the gun shoots balls without it, is it necessary? How do i keep it on?
Does anyone have a text manual on the lv 10?

[Havoc_online]

I responded to your other thread before you posted here

[magzown3]

I am having trouble with shooting my mag w/ lvl 10 indoors where the fps is 250 max. Sometimes the gun will shoot and sometimes it doesnt, especially while rapid fire. I have the main spring in...what could be the reason for this?

[Mickster]

Problem

Hey fitted my level 10 fine no leak which i was expecting, however when i fire a shot it fires fine however when i fire another shot it just burps. If i fire slowly like 1 shot a second it works but as soon as i try and fire fast it burps every second shot.

any ideas please

cheers

[Mr Orange]

Second the Mickster

Hello all,
I have finally found my place in the mag family. It's a classic RT. I just love how the trigger feels, and it's a dead sexy gun. I installed level 10 today. And now I am having two issues. The first is the one the mickster stated above, and the second is that my RT's trigger doesn't feel quite as "reactive" is this normal for LX in an RT or did I do something wrong?

LMK
Leo Jr.

[rehme]

bolt staying forward

ok sometimes when i put my finger in the power feed my lvl 10 will hit my finger and stay back but other times it does what it suppose to when the bolt stays forward it lets the air out this has never happened when i was playing but i am using the .5 carrier with longest spring with 4 shims i am using a mini mag with rt valve sorry if this has already been posted in the thread takes to long to read all of the post

[Havoc_online]

magzown3 the level 10 works best at higher velocities. Since your already using the cut spring, just make sure your using the biggest carrier that doesnt leak.

Mickster, Mr Orange, try turning up your velocity a bit(if you were not already chrono'd)

rehme is the .5 carrier the "broken in" one? Also, have you tried your setting with less shims?

[spawnboy]

sigh...

I've been jacking with this thing for a couple days now and i can't get it to function properly.

Classic 68
Aftermarket PMI Reg
Hyperframe
output at around 700-750

1. I used the 2 carrier with 2 shims and the small spring. Had a small leak down barrel. Would sometimes stop but would start up when I shot again. Did the dollar test and would crush my buck! I took 1 shim out and it would not even fire.

2. I used the 2.5 carrier with 1 shim and cut spring. It just wanted to leak down the barrel.

3. Switched to 2 carrier with 1 shim and cut spring. It made the fully auto reaction with out me touching the trigger.

My head hurts from the clumps of hair I have pulled out.

spawner

[ogre55]

spawnboy: Have you tried using a smaller carrier? Remember that as you switch between carriers you need to keep using the same carrier o-ring.

Ogre

[spawnboy]

stress

Here is what I got now.

My output is at 800+ now and my valve is about as high as it can go.

#1 carrier, the longest spring and 3 shims. I'm still smashing my dollar pretty good. The bolt pushes the dollar in toward the barrel. It gets stuck and my dollar is folded so it's pretty thick.

Am I getting anywhere?

[XxslayerxX]

bolt problem

When i first installed it, it worked great but acouple of days later i was in a game and my gun wouldnt fire. I found out that the bolt wasnt clicking back far enough. I had to use my barrel swap to get it to click in. what should i do?