ALL about the WARP-FEED

[ncsurfer00]

help

Well I just got a used warp today. I got an awesome deal on it because the wires connecting the power source to the board had to be soldered. Fixed those. Now I turn it on and it will only spin when i hit the button. I tried adjusting the sensativity but that did nothing. hElp!

[SocialD]

brand spankin' new warp feed

I'm just bought my first warp and I plan on using it this weekend. I have set it up on my old skool RT and I'm getting ready to set the sensitivity and dwell. I was reading an earlier post and I have a question. Am I supposed to lube the friction wheels before I use the warp? By lubing the wheels I mean rubbing the faces of the friction disks with something like mag oil.

Darrick

[JT2002]

ncsurfer00


go check the airgun site for the warp manual. the switches might be setup wrong. not the dwell ones, but the ones for teh sensor. theres like three sets of pins lined up like..
::
::
::

you need to go to the manual and see which way to set them

[Havoc_online]

SocialD - correct.:)

[JT2002]

or if your lazy like me you can just buy a oil based shell paintball and a half a case of those or more through it should do the job.

[impulseplayer]

Question

Alright well i and instaling a Pro team warp feed onto my impulse. And i was tuning it and i had it set to the sensor part. So thats right correct? And then i was tunning it and i turned it all the way down to where the motor would just barely not spin(like all the way clockwise). and i would shoot and it still wouldnt spin. Whats wrong?

[RoadDawg]

I got a problem with my warp. Don't know the cause so I came to this thread. When I use "wet shells" System X balls, my warp flies but when I use "dry shells" PMI prems it has a hard time loading. What can I do to fix this? Oh by the way they are the same bore. So my question is What's the Dealio? My setup is like this Rico to warp, warp goes to bottom of h/r p/f on my minimag. I've included a pic for reference sakes. Oh and yes they are very nice sheets

[JT2002]

you can use the oil for your mag and VERY lightly rub some onto the wheels to lubricate them. but in my case shooting a case of the "wet shells" through my warp worked well and have had no probs with Evil paint yet.

[Lesman]

Warp breaking balls!

Havoc,

I have an opportunity to buy a slightly used Warp (less than 6 hours of field time)for a great price, which a friend of mine bought new but doesn't like because he was breaking paint in the breach. He was using it on a new classic automag with a level 10 and an all american 2 pc barrel. We were shooting winter paint at CPX and it was about 35 degrees outside. When I looked at it I noticed that he had not lubed the discs and that he had the dwell jumpers all in the non functional positions. When he removed the Warp he didn't break any additional balls so it seems that the rest of his setup is okay. What do you think could be the issues? I plan to install this on my new RTPRO is there anything special I need to know concerning the install. How many dwell jumpers should I be using?

[Havoc_online]

impulseplayer just adjust the dial to the point where it spins reliably with each cycle.

RoadDawg you need to lube your friction disks with dry paint.

Lesman you pretty much answered your own question.:) lube the disks and set the dwell for about 1/4 turn(should be like two jumpers) you should be fine.

[Lesman]

One more question

Havoc,

Things are looking pretty good thanks for your input. I did notice that when I slipped the hose fitting on the end of my powerfeed that it is kind of loose. It takes little pressure to slide it on. Is this normal? It seems like it wouldn't be very durable in the field. Do you have any suggestions on how to snug up the fit?

[Havoc_online]

you bet, go over the first couple of posts in the first page.

use a short thin piece of friction tape(not even enough to wrap around the bottom of the powertube and that makes a big difference....

[Lesman]

Thanks

Havoc,

Thanks for your help, I am heading out to Challenge Park this weekend to give the new warp a try.

[Mike Meeks]

I've got a really basic question. I've got two guns that I'm picking up warp feeds for, for my team. Mine is an RT pf hopper left and the other is a verticle feed minimag. Will I need to pick up the Pro Team 90* for each of these or will everything I need come from AGD? Is there anything else that I would need to pick up? Any help would be greatly appreciated.

Thanks
mike

[JT2002]

dont hold me to this but it looks like you might have to make your own custom adapter for the 90* adapter to fit on the body. something like some sort of tubing just long enough to stick out of the vertical feed and for the 90* adapter to hold on to