One Legged T-Rex (OLTR)

[luke]

The Y grip takes extensive milling to make a MPA-3 and MSV-2 work. The MPA-3 must also be modified. I have built a few and in fact just finished one for a guy in Florida. Probably shipping it in the next couple days. I am going to say that I really doubt that this will work in a Y Grip.

The location of where the cheater must be mounted is the limited factor, I certainly wasn't implying it was impossible, just with my design.

[cougar20th]

There's room, but it will still need machined correct?

Set screws will work but will need to be strategically located to avoid the thinnest part of the ram cavity which is 0.030" thick.
I went with a built in mounting tab so it has a positive and repeatable mount location.

Seems to just drop in as long as that area I asked about is the same as a intelli in your frames.

[luke]

Seems to just drop in as long as that area I asked about is the same as a intelli in your frames.

Like I said, the area you ask about on the cheater is 100% irrelevant to mounting it in ANY frame, it's the foot print and depth that is important. (Did you get my email this morning?)

It is absolutely crucial that the dimensions are relative to the trigger pin hole and/or the frame screw holes, just having the space is only 1/2 the equation.

[luke]

Cougar, take the original model I sent you and drop it into your frame, line it up on screw holes, trigger pin, safety holes and flush to the top, whatever does not fit into your frame will need to be machined away (On your frame)...

[boo]

Would this frame work with a PTP micromag and an xvalve?

[luke]

Did more testing today and found a small issue, that is, small being relative to the whole scope of the project. (lol)
I will have to tweak the entire design, reprogram and machine another prototype. (So glad I did some testing... again>>> )
What's interesting is it was a single, solitary bit of information I trusted from an outside source that went unverified until today. It's completely my fault though because I went against my #1 cardinal rule......
So it's back to work, it will be a few days before there are any more updates.

[cougar20th]

Cougar, take the original model I sent you and drop it into your frame, line it up on screw holes, trigger pin, safety holes and flush to the top, whatever does not fit into your frame will need to be machined away (On your frame)...

OK I get it now. Miss understood.

M86's will need to be machined to fit this.

[luke]

OK I get it now. Miss understood.

M86's will need to be machined to fit this.

Bingo! I had a feeling we weren't on the same page. :)

Do you have the intelli frame modeled?

[luke]

Would this frame work with a PTP micromag and an xvalve?

Probably

[cougar20th]

Bingo! I had a feeling we weren't on the same page. :)

Do you have the intelli frame modeled?

Ill pm you shortly about it

[Loguzzzzzz]

The location of where the cheater must be mounted is the limited factor, I certainly wasn't implying it was impossible, just with my design.

I understand that this is purpose built for your frame only. I never said you said or were implying any such thing. I was trying to answer some other interested people's question, that is all.

[knownothingmags]

unless cost is quite low,
does it make sense to buy this for any other frame other than a lukes frame?

[Loguzzzzzz]

unless cost is quite low,
does it make sense to buy this for any other frame other than a lukes frame?

I see it as a price point issue along with how much work it would take to make it work, and at what cost to make it cost effective for any other frames. From what I recall the Zap Cheater was about $100. Now if you lack the know how and the skill to mod a frame then I see the other alternative as a better option. If you have a luke frame then this is definitely a viable option. . . . . but at what cost. This still remains to be seen.

[maverick13]

I could be for one, depending on price, to mount on your vert frame, or a M86. But most probably on my armada's vert frame.

[luke]

I understand that this is purpose built for your frame only. I never said you said or were implying any such thing. I was trying to answer some other interested people's question, that is all.

It's all good. :)