Venomous Designs "RAIL INTEREST" Must see

After much thought and many designs and ideas along with your help and input we have decided to make a run of 4 designs.
We are still early in the process but we are ready for prototypes and testing.

All 4 designs will be "RTP" length and are designed to accommodate P-Mags and EP-Mags. They will allow you to run any and all wires/hoses. All 4 designs will allow freedom of your front grip placement and also secure a rear asa/snatch grip. All 4 designs will be offere...

First seen by the public at Living Legends 10. This is the new "Necro" automag design. I believe the design was based on the artists spine.



...

Its not on the nummech website, not sure of pricing.

Apparently the hose comes out the top to externally connect to the valve.

No passenger side pics yet I guess.

http://www.pbnation.com/showthread.p...1#post97778905


...

https://www.facebook.com/nummech/pho...type=3&theater



How much? When will it be available? Where do I buy it?:

We need to make a batch of the body blanks then figure out how they will be sliced up. For this level of detail, the body will probably be around 300 (detents included). We'll get more details available a little later!

How do we make a line to get one: We aren...

These are long overdue, but finally here.

Trigger stops are an option now. Ive always used the nylon-tip stops, but they are not cheap. To add those to your order, they are +$5.


Features:
The SplinterBlade & ViperBlade fits & works with:
~AGD Intelliframe
~AGD Y-Grip
~RPG Chimera Frame
~RPG Triton Frame
~RPG Ultra Light Frame

Included:
1 RPG Trigger, as shown.

Price: $35 + shipp...

Last week i started a thread to see what people would like to see made....the majority of you said you would like to see a aluminum minimag style body. I worked a stupid amount of hours this weekend on this prototype. all thats left to do on this is cut the slots in the front...I will do that tomorrow or wed. Check back for updated pictures. Body specs.... -Made from high strength 7075 aluminum -Threaded for dual angel detents -Uses autococker threaded barrels -Angel feedneck threads ...

Had a few extra blanks so i decided to make up a few custom ULE warp left bodies. This has been a project i have wanted to do for a long time and many have asked for it. Available in Minimag, RT and plain fronts.
I only made them in the warp left version...a warp right version could be done in a preorder.

Will post this up soon in the dealers section

...

As promised i finished the machining on the prototypes. Its amazing how much lighter my red smear rt is with the ULE body, X valve and ULE milling...It cut 11oz. off the weight of the gun!!!!!! I might sell some of the prototypes in my SUPER SALE i will be having on the 1st of January. I am currently crunching the numbers to figure out how much to charge. Watch the Dealers section for the preorder.......I only plan on doing one run of them. Body Features: -Vertical feed threaded for use with ange...

Love it or hate it this is my version of a valve cap for a classic valve.

The hole in the back if for a burst disc to make these safe. caps are side drilled to use a spanner wrench to install them.



note: the uninstalled cap has not yet been drilled.....the one pictured on the valve is the 1st piece off the mill....

This rail design was talked about a few months back, there was some interest at the time so I went ahead and did the prototypes to test the programming. Engraving shown would NOT be standard but an add-on. Rails are ULE milled with foregrip slots. Automag rails would have a duel slot for use with both AGD style VASA's. RTP full length slot for 2 screw VASA. Both rails match factory lengths. Milled for all body styles. RTP is 1.00" wide. AM rail is 0.98" Both rails can be pump milled. ...