XMOD BETA Testers ONLY (Questions/Comments)

**pulserifle99** · 03-19-2007, 02:15 PM

tweaked the magnet and nothing

**BigEvil** · 03-19-2007, 03:55 PM

Originally posted by pulserifle99

well i just flashed my mag to the x-mod but when it was all hooked up to the flasher i turned the gun on and it flashed on the led screen the adg 3.2 then low bat, while it was being flashed then nothing after that. So when i hook up that battery to it now it does nothing it doesnt turn on. Is my board fried? i have tried another battery and still nothing

Read the directions again. You missed something.

**A-Tach-One** · 03-20-2007, 10:10 AM

Originally posted by BigEvil

Read the directions again. You missed something.

Maybe. I too had a working 3.2 on one of my boards and once I flashed it to XMod, all it does is blink low bat, no boot up screen appears.

I have tried flashing to other softwares but all it will do is flash low bat now.

**BigEvil** · 03-20-2007, 11:18 AM

Originally posted by A-Tach-One

Maybe. I too had a working 3.2 on one of my boards and once I flashed it to XMod, all it does is blink low bat, no boot up screen appears.

I have tried flashing to other softwares but all it will do is flash low bat now.

Why didnt you tell me this before? Here is what you do...

Take the board OUT of the gun. Be careful not to cause a static discharge that would further damage it. Meaning.. dont wear the fuzzy bunny slippers while you are doing it.

Next.. double check EVERY single one of the pin outs and connectors. Make sure none are bent and that the connectors in the plugs are all secure.

Once you do that, wrap the board in the predator electronics t shirt that TAG sent you. Take it into the bathroom and turn out the lights.

Holding the board (wrapped in the shirt) look into the mirror, and repeat the following;
"I AM THE HUNTER"
"I AM THE HUNTER"
"I AM THE HUNTER"

At which point Bob Sandifer will appear to you and replace the damaged emag board with a predator emag board for only $500.

Let me know how it goes

**p8ntbal4me** · 03-20-2007, 01:53 PM

Originally posted by BigEvil

Why didnt you tell me this before? Here is what you do...

Take the board OUT of the gun. Be careful not to cause a static discharge that would further damage it. Meaning.. dont wear the fuzzy bunny slippers while you are doing it.

Next.. double check EVERY single one of the pin outs and connectors. Make sure none are bent and that the connectors in the plugs are all secure.

Once you do that, wrap the board in the predator electronics t shirt that TAG sent you. Take it into the bathroom and turn out the lights.

Holding the board (wrapped in the shirt) look into the mirror, and repeat the following;
"I AM THE HUNTER"
"I AM THE HUNTER"
"I AM THE HUNTER"

At which point Bob Sandifer will appear to you and replace the damaged emag board with a predator emag board for only $500.

Let me know how it goes

LOL! Somewhere in that statement,.. there is a hint for some "given information"

LOL! Imagine A-Tac in his bathroom with his board and t-shirt. Rubby red night slippers to boot! Tunaball transvestites anyone???!!!

**BigEvil** · 03-20-2007, 03:48 PM

Originally posted by p8ntbal4me

LOL! Somewhere in that statement,.. there is a hint for some "given information"

LOL! Imagine A-Tac in his bathroom with his board and t-shirt. Rubby red night slippers to boot! Tunaball transvestites anyone???!!!

By the end of that night Rudz will be so in the bag that he will wake up in Harlem wearing a school girl uniform and pig-tails.

**p8ntbal4me** · 03-20-2007, 04:43 PM

I really didnt need that visual BE,.... I have to eat in a few hours!

**Rudz** · 03-21-2007, 01:27 PM

scott keep it up and im leaving ur sister with you and im not taking her home with me....

**p8ntbal4me** · 03-23-2007, 01:53 AM

Originally posted by rudz

scott keep it up and im leaving ur sister with you and im not taking her home with me....

(scratching my head)

What the,.....?

(clicks on favorites, opens link to BigEvilonline to get the low down on this classy inside joke)

**mgrubb** · 03-23-2007, 12:50 PM

i installed the software and when i turn it on it shows xmod beta 1.8, i can change all of the settings; mode, rof, dwell etc, but when i am finished and pull the trigger it goes dead. it will not shoot in electronic when i gas it up. am i missing something?

**BigEvil** · 03-23-2007, 01:14 PM

Originally posted by mgrubb

i installed the software and when i turn it on it shows xmod beta 1.8, i can change all of the settings; mode, rof, dwell etc, but when i am finished and pull the trigger it goes dead. it will not shoot in electronic when i gas it up. am i missing something?

The LED cuts out when you pull the trigger. That is normal. There could be a couple of reasons why its not firing. Set the dwell to 20 and try it. If that's not it, then I would look at the solenoid plunger length. It may be too short. Common thing with the Xmod. Refer to the manual for instructions how to set it.

**LorneCash** · 03-24-2007, 12:12 PM

Originally posted by mgrubb

i installed the software and when i turn it on it shows xmod beta 1.8, i can change all of the settings; mode, rof, dwell etc, but when i am finished and pull the trigger it goes dead. it will not shoot in electronic when i gas it up. am i missing something?

Hate to state the obvious but is your ACE set to on?

**hjater** · 03-24-2007, 07:40 PM

emag xmod help

Ok guys here one for ya. I just purchased my emag from one of the guys here on AO iv been doing some reading on the xmod and purchased that as well flashed the emag everything went smooth.

After reading the manual for xmod i tested the noid for the correct wiring and got the bounce in rels..... :-(.... I remember reading from www.xmagworld.com that there are two ways the noid can be wired depending on where the marker was assembled. Please see xmagworld.com then update then scroll down click pc board. There you will see what im talking about. After looking at the page it seem my emag assembled or wired the UK way. Could that be the reason why the xmod software see my noid as being wired wrong?

Also where can i send the marker to be fixed????

**BigEvil** · 03-24-2007, 07:59 PM

Originally posted by hjater

Ok guys here one for ya. I just purchased my emag from one of the guys here on AO iv been doing some reading on the xmod and purchased that as well flashed the emag everything went smooth.

After reading the manual for xmod i tested the noid for the correct wiring and got the bounce in rels..... :-(.... I remember reading from www.xmagworld.com that there are two ways the noid can be wired depending on where the marker was assembled. Please see xmagworld.com then update then scroll down click pc board. There you will see what im talking about. After looking at the page it seem my emag assembled or wired the UK way. Could that be the reason why the xmod software see my noid as being wired wrong?

Also where can i send the marker to be fixed????

Lornecash gets into that in the XMod manual. There is a simple way to check the polarity of the noid using a compass.

**hjater** · 03-24-2007, 08:24 PM

Originally posted by BigEvil

Lornecash gets into that in the XMod manual. There is a simple way to check the polarity of the noid using a compass.

I read the xmod manual then did the bounce test in rels and i got the bounce...the manual say if bounce with fix set to 0 mod: rels then you noid is wired wrong. But im wondering does xmod software see UK noid wiring as being wrong....Help me please BigE im a old school paintballer with a 10yr old boy ready to get started.....