ALL about the WARP-FEED

[JT2002]

ok i think you should try to find harder ball detents for ur spyder, or if its the one that uses teh little metal picee kind of like the old metal nubbins in a mag barrel, then just try to slightly bend out the metal loop so that it sticks into the chamber a lil more, i think that might be your problem. did you ever try to slightly lube the friction discs at all? stick your finger against one side and spin the warp round with teh primer button. hows it feel? a little oily? or no? if not you could try to take some gun oil like Gold Cup and use the prime button and ur finger to rub a small amount of it on each disc side. ill help more later


it sounds like its your detents, but really try to tune the warps dwell too, that will help

[stormtr00per]

thanks guys

I will change the jumpers around, hopefully it will fix the problem (I think I read that the wheel should spin around 1/4 around.) I have used the wire and plastic nubbins which seem to hole the balls in place, but the force of the warp feeds pushes the balls forward so they get stuck, the lvl 10 keeps them from breaking. Does it ever help to feed the balls from the top of the p/f or is it better to feed from the bottom. My gun is hopper right. Where do you get more jumpers? Thanks again.

[mh53eplt]

you can order jumpers from AGD's online store. as for question #2, I would like to know the answer to that one too.

[Star_Base_CGI]

You only want to feed one ball per activation. Theoretically if you constantly need to catch up. You can feed two balls per activation.

Therefore you only want to rotate the distance of 1, 1 1/4 balls or 2 balls if you need to catch up.

As far as the power feed. My best guess is loading the balls from the bottom of the powerfeed reduces your front profile. That is there would be less to shoot on top. It would also cut down your hose length and the distance your Balls have to go to reach the gun. Not to mentioned the number of Balls in route to your gun?


You could try a computer store for jumpers?

[WARPED1]

For optimal performance, reverse the polarity of the flux capacitor, 1.21 gigawats will suffice...............oops, wrong movie!

[amazing_spyderman]

one last time: my sensitivity pot adjuster will not work. how much would it cost to have an agd tech fix it?

[JT2002]

no clue, go call them. or just send it in and they should call you if they need you to pay for it, but they might warrantee it

[hAppy]

my warp is getting stuck
its like the warp is too weak to push the balls up the tube! this ruined a whole day of paintball!
its intellifed, whenever i pull the trigger the wheel will spin, it ll spin than STOP! and it wont load the balls in any further, i checked to see if there were any kinks or turns in the tube, none, i could roll a ball up a down the tube. i tried adding and removing jumpers, made no difference, than i tried a sensitive setup didnt work either.

whats wrong w/ my stinkin warp. i bought it used, either i got ripped or the warp sucks.

[JT2002]

try a fresh, new battery, also can you post a pic of the setup so i can see what it looks like?

[hAppy]

http://photos.yahoo.com/bc/xk3nx/lst?.dir=/mag+progress&.src=ph&.order=&.view=t&.done=http%3a//photos.yahoo.com/

this has a lot of diff. pics of my warp and i feed setup

i hope that ll help

and i tried multiple batteries already ill see if i can find newer ones

thanks for your help!

[JT2002]

ok now u sure theres no tight turn in the hopper? deff try some FRESH batteries. now, does the warp just stop spinning with the balls there like it cant handle it and the motor keeps spinning? or does it spin but nothing move?

[hAppy]

the motor spins but the disk doesnt

[Star_Base_CGI]

Sounds like you need a new drive belt from the store. Scroll up.

[JT2002]

thats what i was gettin to.

[hAppy]

agh i think imma buy a crap load of lvl X and warp parts off the store now!! ARGH!! THANKS GUYS!! SERIOUSLY THANKS ALOT~!!!!