ALL about the WARP-FEED

[hAppy]

Originally posted by JT2002


hey cmon yuji no need to be getting at him. he's new to AO. here bro go to warp manual make sure u have acrobat reader. read through the manual well and u will understand ur warp better. best of luck with it. if u need any more help, just come and post back here, im sure me, havoc, or anyone else are willing to help

thanks for your help! and yuji's sorry im still a newbie to mags and the forum

[JT2002]

np, have fun!

[Yuji]

I was being nice...funny how a little emoticon can say soo much.

[JT2002]

ok. well . lol. ok anways, bak on track...
havoc did a great job with my warp. i love the on/off

[hAppy]

my warp is acting wack again!

when i put in the battery the wheel starts to spin FOREVER!
and it doesnt stop!
MAKE IT STOP!!
whats wrong w/ it?

[JT2002]

try turning down the little blue sensitivity knob inside your warp next to the board

[muirtach]

Are there any know problems that would arise from triming the hose side of the 90* adapter dow to make a more straight path for the hose?

[JT2002]

i dont think so


should be fine

[Pnzrfst]

If anyone is looking for a drop in 12v mod w/ on/off switch I have a bunch of them premade.

[1old68classic]

i'm new to tournaments and i'm lookin into getting a warpfed but will 1 hook up to a right standard feed?

[JT2002]

it will, i used to have mine like that, you can either turn the 90* feed thing to the back of the gun and wrap the hose that way, or turn the 90* to the front, and wrap the hose under teh barrel and into thw warp. but try to save and get a warp body, its that much better

[Star_Base_CGI]

Heres some pitctures of the Warp I just got and put on my Spyder. I also added some technical details since there doesnt seem to be whole lot of content. (Except this thread.)









1 Warped Spyder

[Star_Base_CGI]

I had a larger picture of the board.

So I added it.

[JT2002]

well , most people dont shoot fast enough to really take advantage of a higher voltage, and the hight voltage also makes teh warp more noisy while it runs. what i say it try this, havoc did the mod for me, but it is really very simple. the mod consists of installing an on/off switch which i think is a necessary upgrade because it saves ware on the battery snap wires. i pulled mine out 2 time with the stock setup. the mod also does something havoc ore some1 has dubbed "bigcell" basically 2 9v batts are wired in parallel (i think, i always mix up series and parallel) anyways, what this does for teh warp is it raises i think, amperage but not voltage i think. so what this higher amperage does is keep the voltage going to the warp at 9v, but since the amperage is higher, the warp never suffers from a lowering amperage which, in a stock warp, you could hear and see how after the warp runs for a few secs, its speed slows down a bit. but since theres double the amperage than before, the warp will not slow down for a while which is good becasuse it keeps it up to speed. so thats the ideal setup, on/off mod and bigcell. god its writing lab class all over again!

[Star_Base_CGI]

Well if thats all true, then there doesnt need to be a battery on the second connector. It can just hang empty.

Obviously if the second connector was left loose, to connect with some thing metal it would short out. Ive seen plastic covers that go on the ends of betteries could be put over the extra connector, a piece of heat shrink tubing or a piece of tape.

Ill have to keep my eyes out for those plastic 9 volt battery covers. They go on the end when not in use. I say just put that on the end of battery clip #2 when not in use.