ALL about the WARP-FEED

[deadeye9]

Replace your pulley drive o-ring.

[Imag]

intelliwarp..

ok, i just installed my intelliwire from the intelliframe to my warp and its not working..

i also doubled it up so that it connected to a revvy and the connections at the roller switch are very messy.. but i am sure that none of the wires are touching or anything (i havent got the revvy yet but i put the wiring in for the intelliframe side at least)

what its doing is that when i push the switch down or pull the trigger, the warp doesnt do anything! i push the button down and it goes fine and the vibration sensor still works when i turn the sensitivity on... just not the actual roller switch setup!

i got it to work a little bit but i dont know what the problem is, so help me out plz

[trains are bad]

you need to change the jumper on your board. You cannot have intellifeed and vibration at the same time. I forget what the settings are.

[JT2002]

^^^^^^^^^^^^^^^^^^^^^^^^^^^^
go to agd's site and check out the warp intelli mod web page. in there it should say how to change the jumpers, or look for a warp manual. either wya you need to change em so that u use the intelli signal rather than the vibe

[Imag]

i did change the jumper on the board i moved it from the middle to the end slot.. it doesnt really make sence.. i wasnt sure what guage the wire is im using .. it looked like it was about 22 so ahh i dont know.. i did sauder down all the wire too so it is a secure connection.

i got it to work just a tiny bit but i still am not getting what i should

[JT2002]

first id suggest taking off the revvy wiring and just trying it one at a time, something could be miswired.

[x-mag-newb]

i also got a question

i got a question that is kinda about this and kidna not but u seem like some one that know a good deal of stuff about mags. im buying an x mag from a local prshop and it come already rigged up w/ warp feed and i dont want warp feed i was wandering of i need andyihins to put on the feed neck so i could just slap a halo on there? thanks for your time lata

[Recon by Fire]

The x-mag uses different breaches for the centerfeed and warpfeed. If the one you are buying has a warp breach and nocenter feed breach, you will not be able to mount a hopper directly to it. You will need a centerfeed breach. Most people ordered their x-mags with just a centerfeed or a centerfeed & warpfeed. better ask some questions and see what is included in your purchase.

[x-mag-newb]

x mag breaches

the guys said that it is a warpfeed breech so how can i/ where can i buy a center feed breach?

[Recon by Fire]

If it does not come with an extra breach you will most likely have to inquire with AGD or AGD Europe to get another breach. I doubt yoiu will find anybody to sell you their centerfeed breach.

[Imag]

ahh still cant get my intelliwarp going!! clipped off the wiring for the revvy, and its doing the same thing... heres some pics..

heres the roller switch set up


and my warp board (wow this was hard to get a good picture of)



alright, what did i do wrong plz help

if you guys dont see anything im gonna go buy a new connector dealio that plugs into the warp, the solder sortof melted some plastic on it but i have know idea why that would do anything.. i didnt have enough battery life to get anymore pics though..
thanks

[trains are bad]

Multi-mode warp feedage?

I just realized that if I put a jumper on the top pins and one also on the bottom pins, the warp spins from my intellifeed, but also spins from vibration.

You can unplug the intellifeed cabel and it works fine off vibration. You can also turn the tank off and just pull the trigger without any vibration and it works fine off intellifeed.

Would there be any disadvantage to running it like this in case one or the other system failed?

[B.A.M.]

im going to be getting a warp feed for my rt and i have a few comment/questions
1. im going to do a link with my intell
2. im going to get the on/off 12 volt mod from havoc
3. On a new warp do you get an elbow to fit a center feed or should i just get one from agd store

http://store.airgun.com/index.cfm?fuseaction=catalog.prodInfo&productID=65&categoryID=19

[B.A.M.]

i FOund one at WWA for only 80$. But i have a ?. What do i have to be carful of when i dye my shells. IM going to use rite dye

[E r y k]

you should know that the sensor is built into the right shell... so unless u wanna dip that in, u can only do 1 shell... or you can buy a new set which IMO isnt worth it.