ALL about the WARP-FEED

[Macpaintballer]

I might be getting a warp soon in a trade, and I have a few questions.

1) I plan on linking it up to an Intelliframe, but I'm curious as to if I should also make a link from my revvy from the intelli, so that both as hooked up.. any thoughts?

2) If I hook it up for a Right Power feed and cut holes in my Revvy, will those same holes work if I later purchased a Warp ULE body?

Do any of you find an offset cradle to be more comfortable with the use of your Warp, or does it make little to no difference?

Thanks!

[E r y k]

1. linking it to the warp itself is enough IMO, but if you wanna do the revvy also, it will be fine

2. if the holes are in the same direction as the ULE body, then you should be fine... it might be a tad different, but generally it will probably still be in the right direction

i dont know what you mean by offset cradle, but i use a drop with my warp, and its a little too tight, when i want to shoulder my tank, my mask always hits the lid of my halo

[Macpaintballer]

and offset cradle is something like in the picture... I figure if you move the tank towards the warpfeed, it wll balance the weight between the marker and warp.

[E r y k]

hmmm thats interesting... but the warp doesnt put the gun off balance that much imo...

[jewie27]

why would it matter when you will be holding the Mag with TWO hands.

[RoadDawg]

ok I'm going to attempt to organize all the info on the warp since most ppl don't go looking at the airgun site. I will fill in anything else I remember later...Please read on through my next couple of posts and feel free to ask any questions or make comments

Warp Manual
overview
what you need
jumpers
sensor
run in
maintenance
batteries
feed tube
hopper
lefties
automag bodies

Warp detailed view

Intellifeed to Warp Interface

Hopper Mods for Warp Feed

12v mod

Warp to Angel Interface

PTP 12v drop-in kit

warp mod pricing.
by popular demand.
here are my prices.

on/off - $10
big cell - $15
on/off w/ bigcell - $20 <--All you need and what I recommend.
12v mod - $20
12v w/ on/off - $25
l.e.d. - add $4
fix broken warp - case by case basis - pm me.

You MUST also include insured return shipping.

12v Mod link doesn't work. Need to figure out what I need and how to do it?

[E r y k]

do you want to do the one with the 12V regulator?

[RoadDawg]

do you want to do the one with the 12V regulator?

yup. I looked at Havoc Online after I posted this. Figured out what I need etc.

[E r y k]

alrighty... good luck with it.

[Cypher333]

[TipMan75]

WarpFeed on a Tippman 98c

Hi there,

I want to know if I need a special feedneck adaptor to accomodate the warpfeed. I just bought one... but I am unable to fit the piece that goes on the feed neck of the marker!!

thanks in advance!

[toast181]

Warpfeed issues....

I bought my mag used about 3 months ago, and it came with a warpfeed... Just recently I have decided to use the warp feed, so I popped a battery in, and it just kept running, and running and running. I decided this was bad for the battery, since warps are supposed to be vibe activated, so I looked at the AGD manual on airgun.com, and read something about the carbon brushes need to be worn in. Since I didn't know how used the warp was, I ran a nine volt through it (it's a 9volt system). After the first 9 volt died, I put in another, and it just kept running, regardless of the jumpers i changed, or the sensitivity level on the potentiometer... Can anyone help?

[E r y k]

either your sensor is faulty, or the jumpers arent set right...

are the jumpers put in vibration sensing? or intellifeed? will it keep turning if you turn the blue potentiometer all the way down?

[voodooaddict]

Chops with Warp.

Currently I'm getting an incredible amount of chops on my Warp Feed / Dragunfly LCD / Revy 12V Setup

I know the vertical ball stack with the Powerfeed adapter isn't quite lined up like it's supposed to. The ball stack looks like the "bad" picture.



And I bought an additional powerfeed adapter adapter so that I can cut it down in hopes of shortening it up and lining up the stack correctly. Will this correct the chopping issue? (Waiting for the new powerfeed elbow to get here.)

The Dragonfly LCD is a closed bolt marker (a knock off autococker with ElectroFrame).

If I just drop a simple VL200 grav hopper on the marker it won't chop. It has an anti-chop bolt that will stop forward movement if there is a ball halfway into the chamber. So I'm having difficulty figuring out what is causing the chop.

[JT2002]

are you sure your balls are brakeing in the chamber? also part of your problem is it sounds like the gun doesnt have eyes, (does it?) this is problematic because it can freely become a blender. also, part of the prob is also that u have to use the vibration sensor, you need to try and get it tuned each time u play so it goes on all the time and gives you a good dwell time. if it doesnt turn on often enough or long enough it can cause slack in the ball stack making it easy to chop. also make sure u have fresh batteries. you also need to fixx the ball stack issue