ALL about the WARP-FEED

[B.A.M.]

on havoc online it says that you can dip the shells in w/ the sensors and just let them dry

[02vertcocker]

Hey, I have a question, my warp wont spin when I shoot my classic valved mag. I know it is on, and I know it works, because if you push the button it will spin. I used to run an intellifeed on it, so it was never a problem. I have tried adjusting the dial on the side, but it had no effect.

Any help is greatly appreciated.

[E r y k]

hey 02 vert cocker....

you have to take off the black housing on the right side and fix the jumpers so its on sensing mode instead of intellifeed...

i dont have my manual right now so i cant tell you the exact positions... sorry.

merry xmas.

[MTU Paintball]

Hi; got some questions on the warp. Any help is appreciated.

1) I did the emag power mod from robagd.com and the 12 volt regulator got too hot to touch. I added an aluminum heat sink, but the heat sink got just as hot. I'm worried about melting through my shells. Anybody do this mod?

2) Is one 9 volt battery fast enough? I had my bps set at 18 and was getting chops. Should I knock down my bps or go for the 12 volt?

3) I have the emag link on my warp and have three jumpers on the dwell. Anybody know from experience what is a good number of jumpers?

[cabldawg]

well I have my warp set with an 18volt mod and only 2 jumpers I don't have any over heating problems

[B.A.M.]

Hey, I have a question, my warp wont spin when I shoot my classic valved mag. I know it is on, and I know it works, because if you push the button it will spin. I used to run an intellifeed on it, so it was never a problem. I have tried adjusting the dial on the side, but it had no effect.

Any help is greatly appreciated.

Remove the shunt from the top and put it in the middle on the board right next to the plug in

[Terminal Frost]

Feed Tube Length???

how long of a feed tube can you run with the warp feed???

[B.A.M.]

ive heard as long as it is from a pack on you back to you gun so pretty far

[Cilio- Knightmare Tango]

T-Shaped Feed

I just purchased a Warp feed and a ULE hopper left body. I was planning on using the T shaped power feed (came with it) and sending the hose straight down to the warp (hopper is an Egg, so it's not in the way).

My question is... the small plastic attacment that fits perfectly when connected directly to the WL is extremely loose on the T shaped feed. Is there a piece available that fits tightly on the T-feed wih the other end fitting properly on the hose? If not, any suggestions? I was trying not to have to use tape or something.

Thanks for any info and help.

[UTDragun]

Im sorry if this question has already been asked

I heard that if you use the 12v mod, the motor will heat to higher temps than normal and melt some parts on the board. How do you prevent this?

also, is the ptp faster or same as agd's?

[Jazkal]

I haven't heard of this with a 12v mod. I have heard of people wiring up 18v and frying the board.

[E r y k]

im running 2 9v's wired parallel so overheating

[UTDragun]

im running 2 9v's wired parallel so overheating

you mean no overheating? like a "big cell" set up?

[Jazkal]

2 9v's in parallel only produces 9v of output. I was talking about some people were connecting two 9v's in series for 18v of output, and that was frying the board.

[E r y k]

yeap... no problems, battery life is extended greatly.

ive ran a good 9-10 cases through it so far... and ive probably used ~4 batts