ALL about the WARP-FEED

[Lesman]

Inteli Feed Question

Havoc,

I converted my warp to inteli feed per the directions on the AGD site. One thing that I noticed is that the gun still responds to the vibe sensor like when the warp gets bumped or something like that. I have the jumpers the way the directions show. What should I do? Is it going to be a problem during gameplay if the warp is receiving signals from the switch and the vibe sensor?

[Havoc_online]

johnnyringo how old of a warp is it? what kind of batteries? are you sure your jumpers are all in the proper place?

Lesman take out all the jumpers on the right set of pins, just leave the top(neg.) pins connected.

[johnnyringo]

havoc I jsut purchased the warp from paintball wizard. I was using duracell. I have both the top and the bottom jumpers on; on the right side of the warp board. Should I take the bottom off as well? I wonder if that was the problem!!

[Havoc_online]

intelifed - just leave the top jumper on.
as for it being a new warp, that may be it, you may need to break in the carbon brushes on the motor(see run-in)

[SkElL~ObIsSiS]

i just gopt a used warp and i thnk the previous owner took out the recoil sensor, can anyone point one out on a pic of a warp for me?

[Yuji]

Weak Warp

Why would a brand new Warp that has seen some playing time run slow or not at all? It just doesn't turn as fast as my other warp. Both are new and have the proteam 12v mod. It will turn without balls but as soon as it's under load it turns very slow or not at all. Tried new batteries and checked the jumpers and still not working properly.

[1stdeadeye]

Thanks!

This thread is great. I was trying to get my warp set up on my X-Mag. Once I put everything together, I couldn't get my 90* adapter to fit my hose. I pushed and pushed. I was about to post, read this thread, and realized I left the Feed tube adapter on my R/T. Duh!

Question, what is the best way to cut the feed hose?

[Havoc_online]

SkElL~ObIsSiS The vibration sensor is a disk mounted on the shell(you can't miss it). You might try checking to see if your jumpers are set up properly and if they are, check your dial sensitivity. If nothing works, check that the board is connected to the vib. sensor(two springs) properly.

Yuji Remember that the warp needs to stay fed, keep paint in the hopper. Check your ballstack for restrictions(see if it feeds well without being connected to the body). Finally, hows the paint fit the friction disks?

1stdeadeye Glad the thread helped out! (Just use the sharpest razor you can find)

[silenttype]

look here

warp exploded view
http://www.airgun.com?downloads/warpexploded1.pdf

[SkElL~ObIsSiS]

I just got a used warp and I cant get the thing to activate at all, I got an e-mag but am in the procces of making a link cable and just wanted to use the warp with the gun on vib, but when I set it to its most sensitive setting and slap the piss put of it nothing happenes???? im confused, where is my vibration sensor? is it missing? the jumpers are set on the bottom two in the vib. position

I can get it to spin with the white primer button but thats it...

[Yuji]

Well...heres my trix with my stealthy warp mod I'm still working on getting a smaller 45/4500 and a suitable drop forward but u get the picture, I also shortened up my warpfeed adapter and feed tube some more...what do you guys think I hope no one steals my idea and makes a bunch of $$$

[ski]

That's definitely a unique setup. Not really my thing but I give lots of credit to you for the effort put into it, awesome = ).

Now on to my questions. I just got my 12v mod done to my pro-team warpfeed, running it on an Adrenalin Impulse. I have the issue with it constantly spinning so I'm going to look into a capacitor for it as suggested on this thread. However, just out of curiousity, how much work would it take to leave it running off of a 9v battery like it is "stock" and simply hooking up an on/off switch to it. Furthermore if I can't get this mess cleaned up how much do you charge to have the 12v mod, LED and on/off switch done Havoc? I consider myself fairly proficient, the wiring has not been an issue at all...getting everything to fit inside most definitely has been, hehe. With the LED, on/off switch and plus now a capacitor, I'm just not sure if I'll be able to get everything in there. Any help would be appreciated, thank you very much.

Mike
[email protected]

[ski]

Ok...well I got a 100 uf capacitor and put it on the output side of the 12v reg and now it doesn't work at all...I take it off it won't stop spinning, I put it on it won't spin at all. Any advice would help, thanks = )

[Yuji]

I realize it looks unorthodox but the warp/halo feels more comfortable in this position and absolutely rocks when I run a remote. I obviously would prefer to run a tank on the gun..but until I get a lighter/smaller one i will make do with this. Thinking outside the box is sometimes a good thing We'll see in a couple of years how ball feeding products evolve...But I bet dollars to doughnuts that traditional hopper configurations are going to change drastically. I'm going to keep working on this project and will post pix when it's all done.

[Mike Meeks]

Well, I have both Warp Feed kits now and it looks like it should be pretty easy to put together and link to the inteliframes but I have two more questions.

1. I'm having a hard time getting my rev and the lower warp feed adaptor to fit in the warp. They both seem just a little to big. Would you recommend unscrewing the shell slightly inserting the piece and then tightening the screws back up or would this not be good for the warp? Otherwise should I just sand down the rev and the adaptor until they fit?

2. The Minimag I'm installing the warp on does have one of the old bell shaped verticle feed tubes. Can you recommend something to use as an adaptor for the 90 to attach to? I was thinking of cutting off the neck of an old VL 200 or finding something in the plumbing department that has the same dimensions.